http://www.partselect.com/Schematics/Frigidaire/Frigidaire_Thumb/FM2317KV.gif
See part F61 in the diagram

Fan Blade

PartSelect Number PS2361234

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Unusual Noise.
  • Compare At

    $10.63
  • You Save

    $1.77
  • Your Price

    $8.86
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 5 reviews What's this?
1-5 of 5
 

29 of 30 people found this instruction helpful

Parts Used

  • Fan Blade

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsWrench(Adjustable)

CustomerMilton from Camp Hill PA

Broke a blade off of the fan

When cleaning the coils on your refrigerator always remember rule number 1, unplug it first. I was cleaning the coils and hit the fan blade while it was moving with a brush, thus breaking off one of the fan blades. I ordered a new fan and installed it in about 15 minutes. Very easy repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 14 people found this instruction helpful

Parts Used

  • Fan Blade

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench(Adjustable)

CustomerJohn from Morgantown WV

Brand new refrigerator, but evaporator fan blade broken, causing considerable vibration and noise.

Really, really, really easy:
1.Unplug refrigerator (electrical safety).
2.Remove cardboard cover at bottom of refrigerator (two short self-tapping bolts) with a wrench.
3.Pull old fan blade off fan motor shaft (just held on by a compression fitting--no tools needed).
4.Push new fan blade on shaft.
5. Replace cardboard cover.
6. Plug in refrigerator, write nasty letter to Frigidaire.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Fan Blade

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerAlbert from Bristol IN

Broken fan blade

Pull refrigerator away from wall, being careful not to kink or break water line to ice maker, unplug refrigerator. Using 1/4" nutdriver, remove cardboard lower rear panel, bottom lifts out. Fan and motor are now directly in front of you, grasp the moter to stablize it, and using your other hand, pull fan hub from motor shaft. Be sure motor shaft is clean before reinstalling new fan blade, press new bladr onto motor shaft, until center of blade is centered on outlet side of fan housing. spin blade by hand to insure clearance. Plug refrigerator in and observe operation of fan, refrigerator needs to be calling for cooling for this fan to operate. Reinstall cardboard panel and move refrigerator back into position.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Fan Blade

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRaymond from Houston TX

I broke the fan while cleaning the coil

The broken fan made my refrigerator sound like a lawn mower I pulled the refrigerator out of it's nook and disconnected the power, removed the back panel with my battery powered drill motor, slid the old fan off of motor shaft, slid the new fan back on ran it to make sure the problem was corrected. The entire repair took less than fifteen minutes and was as simple as it could be. Please be careful when cleaning your coil, as the fan is easily damaged if you should contact it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Fan Blade

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerTIM from Lockport IL

Broken fan with vacumme cleaner

I remembered to unplug first. took the little cover off on the bottom, unscrewed the 3 screws. then just held the base that the fan is on and pulled rite off, pushed the other one rite on. it took me five min, i want to say thanks to parts select, had the part, fast shipping, great job, thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5