| |
1 of 1 people found this instruction helpful
Parts Used
-
- Crisper Cover Support - Front and Rear
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerKristina from Woodbridge VA
Broken shelf support stud
I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJeneen from CHARLOTTE NC
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:30 - 60 mins
ToolsPliers
CustomerJOSE from Miami FL
Crisper support pins were quite tricky to secure
The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerMichael from Blanding UT
Support broke and missing parts
Lost the freezer shelves so had to replace them...easy. The shelf bin holder broke so it needed to be fixed...piece of cake!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMarilyn from Bellport NY
Door bins broken and crisper cover support broken
Replacement of bins were simple the crisper cover supports were a little more time consuming since the manufactured piece were glued in. I used a tool that has a 30% tip and hooked the support and pulled in out part of the way and pulled the rest out with my fingers. All in all a simple job...I took the opportunity to do an addition cleaning of the inside of fridge with my extra time. Would also like to say that my parts were delivered within 24 hours of ordering them and the website made purchasing easy and no second guessing, since the model had an exploded version of all the parts available. Thank you
|
0 of 1 people found this instruction helpful
Parts Used
-
- Crisper Cover Support - Front and Rear
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerCharles H from Beverly NJ
Chrisper drawer support was broken
Due to the nature of the support deisign and installation which was unusual I watched the video on how to extract the old broken support and install the new one, odering the new part was simple as the view privided in the parts section was specific and and easy choice to make, cost was very minimal and I received it the next day due to my being in close proximity to the shipping point, thank you and my crisper is very happy and so am I.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJohn from Princeton NJ
A crisper cover support had broken
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerAlton from Seaford DE
Renters broke the door handle and the support for the crisper
The handle and trim piece were very easy to change. Four phillip head screws and it was done. The only difficult part was getting the broken crisper support out of the the wall of the refrigertor. Once it was removed the new one just snaped into place it was easy to replace.
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerDerek from Graham WA
Plastic shelf support broke
Took out the support and put back in the new one.
|
0 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerPeter from Nashville TN
Wife broke water dispenser actuator
I had seen technician remove cover for warranty repair. If I had not I would have been in trouble... I removed tray exposing screws, removed screws and lifted off cover. I then pulled off connector to circuit board. I removed the three screws holding the broken dispenser part and removed it. The reverse was easy. The hinge cover was easy since I had learned to slide it forward FIRST (that's when I broke it). The shelf supports were tricky. The old ones would not come out. I sawed them off with a serrated knife and then picked the pieces out. Installing the new ones wasn't going well until I realized that I had to hammer the pegs in. Then they went right in.
|