| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerSandra from Litchfield NH
Broken crisper drawer supports, cracked door shelf bins, broken freezer door handle.
My freezer door handle has been broken for probably 4 or 5 years - ex husband was not a handy man whatsoever. Never even thought to search for a replacement. Two door shelf bins were cracked and I had to be careful with how much weight I put in them. Then the crisper drawer support pegs broke. I couldn't do without that, so I finally searched on line for replacement parts. This web site was so easy to use - detailed diagram left me with no doubt that I was ordering the correct parts. My order came within 4 or 5 days of my placing it! The parts were very simple to replace. I can't believe how long I waited. But $100 in parts has made me very happy!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJeneen from CHARLOTTE NC
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:30 - 60 mins
ToolsPliers
CustomerJOSE from Miami FL
Crisper support pins were quite tricky to secure
The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerFredey from Andrews TX
Crisper supports were broken
Drove pins all the way thru supports & then pryed support off. Tapped new supports in place. Watch the vidio on installing new supports. I probably wouldn't have been able to get the supports off without the trick I learned to just knock them on thru. Took all of 5 minutes to replace 4 supports.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerDale from Fort Wayne IN
Broken crisper supports
The video was very helpfull. They were fixing the same refrigerator that I have. I punched in the set pin on the old part. Removed the old part by prying it out with a putty knife. Inserted the new part and drove in the set pin. I was glad that PartSelect had my parts. The repair shop in Fort Wayne Indiana did not even show this repair part on their computer.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerwilliam from bellmawr NJ
Broken support
had to remove broken by pushing 1pin then remove.
put new one in reset pin done.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerElaine from Canon City CO
Pegs on shelf support and door bin were broken during a relocation
The door bin was an easy fix, just slip the edges into the raised supports of the door.
However, replacing the pegs which support the crisper bins, was a lot more difficult. Removing the old peg was not as easy as one might think. Because the pegs were broken, there was nothing to grab hold of. Having the replacement peg was helpful in determining how the old one was attached to the refrigerator wall. I needed to get a small blade screwdriver, and also a thin pocketknife blade, behind the base of the peg and wiggle them enough to get hold of it with the tip of needle-nosed pliers. The peg broke off in several pieces. Some I could remove by snapping them off and others had to be pushed in behind the refrigerator wall because there was no way to get hold of then. Once that was done, the new peg popped easily into place.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJohn from Princeton NJ
A crisper cover support had broken
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.
|
2 of 7 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers, Socket set
Customercharles from maylene AL
Ice maker quit despensing
Had to test unit to see where problem was.
Remove ice maker box, and base, PITA, to gain access to plug for testing.
Test for 120V going to motor via plug behind ice maker. No power here = problem is in power board. If 120v exists, problem is with dispensing motor.
Ordered part, removed front cover
Removed old board
Replaced
Works great.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerjohn from mount airy GA
Bracket that holds crisper shelf broke
Have not really done the repair yet( frig is still to full of Thanksgiving leftovers) but I am sure that with the video that was provided by this site the job will be very simple. Many thanks to the person who put the video together.
John Donnelly
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerSTEVEN from NEWPORT BEACH CA
Crisper supports (2) broke and shelf had no support.
I read other comments and most suggested the fix is less than five minutes and a couple tricks (push the remaining piece into the frig if you can't pull out with pliers)and I did exactly that. Parts came in 2 days, repair took 5 minutes - it took longer to open the package. My wife thinks I'm a star!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerEdward from Chandler AZ
Drawer support was broke
Pried the broken support insert out with a screw driver and pulled it out with pliers, then inserted the new and pressed it in and Presto the drawer now works good again.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerKarl from Manchester NH
Broken shelf support
Punch out center of old support, then pull it out. Insert new suppport, insert center and tap flat with hammer. All done!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerLJ from McCordsville IN
The drawer slide had cracked and was no longer holding the drawer in place
I had removed the current cover from the refrigerator by lifting it out of place. I removed the glass insert and placed it in the new crisper cover. I placed the new assembly into position, added the drawer back into the drawer slides, then the refrigerator was back to new!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerBrandon from Atlanta GA
Had multiple supports snap off the side walls
It was pretty easy. The hardest part was getting the supports that had snapped off out of the walls of the refrigerator. Once that was accomplished it was a breeze.
|