2356992-2-S-Whirlpool-3412D024-26-Sealed Burner Cap with Electrode
2356992-2-S-Whirlpool-3412D024-26-Sealed Burner Cap with Electrode 2356992-1-S-Whirlpool-3412D024-26-Sealed Burner Cap with Electrode 2356992-3-S-Whirlpool-3412D024-26-Sealed Burner Cap with Electrode http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/50074.gif

Sealed Burner Cap with Electrode

PartSelect Number PS2356992

This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows, but will not light.
  • Will Not Start.
  • Element will not heat.
  • Gas smell.
  • Compare At

    $34.73
  • You Save

    $5.79
  • Your Price

    $28.94
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 21 reviews What's this?
 

10 of 14 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Wrench set

CustomerAndrew from Framingham, MA

Burner replacement and gas supply replacement

Unscrewed burners (1/4 turn and pop out) then removed set screws, opened top of range. Used 1/2" wrench to remove gas pressure fittings, popped new ones in, replaced wires. Placed top down and then put screws in to minimze movement of tubes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Sealed Burner Cap with Electrode

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerGeoffrey from Columbus, GA

Burner didn't self ignite or control flame

The burners turn and lift. I replaced two. One turned very easily, the other was stuck so I used liquid wrench and plumbers pliers. I did get it off. Once off, the old wires slipped right off and onto the new burners. Those twisted on very easily. Good as new easy breezy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Sealed Burner Cap with Electrode

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench (Adjustable)

CustomerRichard from Los Angeles, CA

Burners would not ignite flame...had to start with match.

Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Sealed Burner Cap with Electrode

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerDimitri from Cambria, CA

We live near the pacific ocean - the air is "caustic" from the salt. The burner was rusting out. And the flame was uneven.

The repair was a no brainer - twist to release the old burner - disconnect the spark wires. connect the spark wires on the new unit - drop it in and twist to lock - about 2 minute job

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Sealed Burner Cap with Electrode

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerJohn from Ridgefield Park, NJ

Old burner that didn't light and was burning poorly

I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!

Help other customers find the most helpful instructions.

Were these instructions helpful?