Quick Question!

Have you ever purchased from PartSelect.com before?

235672-1-S-GE-WB21X10046        -Oven Cavity Temperature Cut-Out
235672-1-S-GE-WB21X10046        -Oven Cavity Temperature Cut-Out 235672-2-S-GE-WB21X10046        -Oven Cavity Temperature Cut-Out 235672-3-S-GE-WB21X10046        -Oven Cavity Temperature Cut-Out http://www.partselect.com/Schematics/GE/00113379i01.gif

Oven Cavity Temperature Cut-Out

PartSelect Number PS235672

Also known as fuse.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Won’t turn on.

Compare At

$32.09

You Save

$5.35

Your Price

$26.74
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.5 / 5.0, 5 reviews What's this?
1-5 of 5
 

16 of 27 people found this instruction helpful

Parts Used:
  • Oven Cavity Temperature Cut-Out
Level of Difficulty: Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: michelle from virginia beach, VA

Original part was fried

Had to remove microwave from the wall. Then disassemble entire top assembly to get to the part. Easy enough to replace after that. Then just reassemble and reinstall. About 2hrs. total

Help other customers find the most helpful instructions.

Were these instructions helpful?   

12 of 18 people found this instruction helpful

Parts Used:
  • Oven Cavity Temperature Cut-Out
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Steven from Gardiner, ME

All power out. No display, not operational

Remove microwave and set on flat surface. Remove all screws on top. Remove all screws around back edge holding top on. Finally remove the screws on botton holding top on and remove top. On left side on top, remove 6 screws holding black channel in place. Also remove 3 screws holding metal top in place. Now lift black channel up and unplug 2 wires on cutout. Replace cutout and reinstall everything in reverse order. Worst part is taking microwave down and reinstalling.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 13 people found this instruction helpful

Parts Used:
  • Oven Cavity Temperature Cut-Out
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Wrench (Adjustable)
Customer: R C from Eglin Air Force Base, FL

Oven shut down when tco (thermostat) detected overheat. Once cutoff, it has to be replaced not reset.

The spacesaver is mounted over the stovetop. I removed the oven, then removed all the screws from the cover. Removed the cover and located the TCO and removed the wiring and the TCO. Ordered the part VIA internet and replaced it . It helps a little that I was Radar tec. and taught Electronics for 10 years and repaired lots of Microwaves. However anyone could do it just watch what you remove and replace in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

11 of 19 people found this instruction helpful

Parts Used:
  • Oven Cavity Temperature Cut-Out
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Wrench set
Customer: Larry from Brookfield, CT

After 3-4 minutes microwave display would blink and unit would just cut out.

This was the second time I've had to open up the microwave. 1st time display would blank out but system would continue to operate. Found solder connections on board to LED display were defective. Resoldered and unit was fine. This time I found the connection to the oven cavity temp cut-off was bad, plastic connection cover melted. When unit operated bottom lead and wire would heat up. Couldn't measure a Discernable distance so either wire or connector connection surface was not sufficient to carry the current. 1st replaced sensor still wire heated up. Replaced connector and there was no sign how heat from resistances.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 14 people found this instruction helpful

Parts Used:
  • Oven Cavity Temperature Cut-Out
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Neil from Williston, VT

Lack of power to unit

This is the second time replacing this fuse, last time was exactly one year ago. The first time I replaced it, I removed the oven from the wall & disassembled a number of things to reach the culprit. This time I left the oven mounted & was able to access the 2 grille mounting screws on the top of the grille & remove it. Next comes the black plastic air deflector held by two screws & is mounted in front & on the right, it is shown on the parts list just above part #1434. After removing it, remove the two silver cover screws in the front, this cover also doesn't have a part # but is shown to the right of part #1410. At this point you can lift this cover enough to access the fuse which is on the left & held in place by one tiny screw through the clamp at the top, (careful not to drop it when removing). PS: Don't forget to cut the power to the microwave before starting!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5