2354686-1-S-GE-WR29X10085-Icemaker Stripper Arm
2354686-1-S-GE-WR29X10085-Icemaker Stripper Arm 2354686-2-S-GE-WR29X10085-Icemaker Stripper Arm http://www.partselect.com/Schematics/GE/00137807i06.gif

Icemaker Stripper Arm

PartSelect Number PS2354686

This part strips the ice from the icemaker mold during the ejection cycle. Used on rear mount icemakers.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Compare At

    $35.45
  • You Save

    $5.91
  • Your Price

    $29.54
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 8 reviews What's this?
1-5 of 8
 

34 of 48 people found this instruction helpful

Parts Used:
  • Icemaker Stripper Arm
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Errol from Mill Creek, WA

Icemaker stripper arm tine broke off (by me), causing ice to remain and not discharge normally. The cause was a stripperarm tine becoming caught under an opposing tine in the icemaker preventing it from discharging ice altogether.

Installed the new stripper arm per instructions - an easy installation. After a few cycles the original problem happened again, the stripper arm tine caught under an opposing tine stopping the unit from operating. I removed the stripper arm, after marking where it was caught, and filed it down so it wouldn't catch anymore. Icemaker works fine now. Troubleshooting tip. If a stripper arm tine is caught under an opposing tine, gently slide a screwdriver between them to release it without breaking the tine. Remove the arm, file it down 1-3 mm, and reinstall.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 29 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Charles from Bakersfield, CA

Dead ice maker.

Replaced ice maker. Required the removal of one screw and disconecting the control cable.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 17 people found this instruction helpful

Parts Used:
  • Icemaker Stripper Arm
Level of Difficulty: A Bit Difficult
Time to do repair: Less than 15 mins
Tools:
Customer: William from Abita Springs, LA

Broken tine on stripper left one cube to jam the ice maker

There were no fastening hardware. The plastic stripper just snaps in place. I had to be patient and could not get it out until I put upward pressure on the stripper.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used:
  • Icemaker Stripper Arm
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Kevin from Anaheim, CA

Piece broke off on stripper causing ice to jam

tab on right top, flat insert on left. Pull up, toward you and to the right. It pops off. No tools needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used:
  • Icemaker Stripper Arm
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Amy from Henderson, NY

Ice maker was making no ice.

snapped in the new stripper arm where the defected one was.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 8