Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2353327
The grate foot pad attaches to the bottom of the burner grate to prevent the cooktop from being scratched. It protects the stove top by cushioning the grate on your gas range. Over time, these feet may crack or deteriorate, and you will need to replace them. This part is a genuine OEM replacement part, made entirely of rubber. Because this part is sold individually, make sure to order the quantity that you require. Before beginning this repair, ensure that the surface is cool to the touch.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Unpllug the cooktop and turn off the gas supply. Remove the grates and burners.(they just lift out). Using a torx screwdriver, remove all the torx screws below where the burners sit. There are three screws per burner, except the power burner which has only two screws. Genly lift the stainless steel cooktop, separating it from the rest of the enclosure. Hold the electrodes with one hand, while gently twisting and pulling the wire connector off. Now, remove the aluminum covered foam piece. You will now have acess to the wiring harness assembly. Disconnect the quick connectors and replace with the new assembly. Re-assemble in the reverse order and you're done. About 1.5 to 2 hours. Good Luck
Help other customers find the most helpful instructions.
Were these instructions helpful?
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Repair to range went real well, Lifted range from counter. Removed eight screws that secure burnerassembly. Lifted burners from it's position, andremoved igniters. Installed heat srink at burner connections so as to ensure high voltage wouldhave no leaks. Removed insulation, and installedspark module.. Reassembled unit, placed in counter cut out, put 110 volt cord into outlet.Tested all burners, everything worked great..The repair took about hour and 15 minutes.Have fun and be careful...... THE END
First I had to take out the end caps on both sides of the upper rack - easy enough - you push in the direction of the arrows and they open up and come off. Then I took the rack off. Using the smallest allen wrench I could find in my ex-husband's set that he left behind (yay!), unscrewed the old rack assembly. The (blue) adjuster level doohickey popped out when the old assembly came off, but it was easy enough to fit that back in properly by looking at the right-hand one that was still in place. All I had to do was fit the new rack assembly into place, put back a few screws, and slide the rack back into place. Put the end caps back on and you're done. Maytag should offer free replacements for this part, IMO- the wheels are too flimsy to begin with, our dishwasher is only four years old, and the new part is pricey, at $29.45 a pop.
Ordered the parts online. They came in just a few days and all 3 repairs took me less than 10 minutes!
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.I do use silicone to help hold the foot but it still won't hold
Removed top grate. Removed burner head . replaced with new burner head. Replaced grate.Very simple replacement. Old burner head was warped with age.
there were no grate pads so it was easy to add them.
I had to drill the hole to a larger size to enable the foot to fit.
Used scribe to remove grate foot plug still in grate inserted new foot.
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.