Quick Question!

Have you ever purchased from PartSelect.com before?

2353273-1-S-GE-GXRTDR-In-Line Icemaker Filter
2353273-1-S-GE-GXRTDR-In-Line Icemaker Filter http://www.partselect.com/Schematics/GE/00120991i07.gif

In-Line Icemaker Filter

PartSelect Number PS2353273

This filter works only with plastic lines. It has a new design with quick connect fittings at the end of the filter.

This part works with the following brands: GE, Hotpoint & Kenmore.

Compare At

$26.15

You Save

$4.36

Your Price

$21.79
Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 6 reviews What's this?
1-6 of 6
 

27 of 36 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Frank from Las Cruces, NM

Ice make auger rusted, unable to serve clean ice.

Replacement auger and ice bucket assembly was perfect. Just had to remove the front door/flap assembly from the old unit and screw on to the new. The water filter kit took more time to read the box instructions than it did to install. Perfect. Am very pleased with the service/value offered by PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Wrench set
Customer: Kelly from Atlanta, GA

Water dispenser not dispensing water

the back plate was removed and the solenoid part was removed for ordering. when installing, the same plate was removed. then the part was installed. also we put in an in-line water filter. that just included splicing the common inlet tube prior to the soloniod entrance and installing the filter.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jane from San Dieg0, CA

Replacing filter and auger/ice bucket assembly

After I realized that I needed to take the front and door off the old ice bucket (which involved removing 4 screws) and mount it on the new part (putting in those 4 screws), the job was easy. Installing the new assembly requires shoving it into place without really being able to see how or where it attaches, so I wasn't sure it worked until it produced ice a few hours later, and it did.

The filter on the fridge was more than 10 years old, but the new GE Smart filter and its adapters screwed and snapped into place easily. Subsequent filter changes will be simple - just a snap!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 12 people found this instruction helpful

Parts Used:
  • In-Line Icemaker Filter
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Wrench set
Customer: Allen from Port Ludlow,, WA

After market ge water filter spud fitting broke off

It originally appeared that an easy out would be required to remove ferule from piping line, but later it became necessary to cut old broken fitting off and replace with compression fitting in replacement kit. Total time to repair after all tools were on hand (needed to buy tubing cuter) was about 45 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: LARRY from McGregor, TX

Ice bucket auger was rusting and getting the ice dirty.

Removed the old ice bucket from the freezer and placed the ice in a plastic bag to reuse. Removed the ice bucket front cover by removing six (6) screws. Installed the old front cover to the new ice bucket by using four (4) screws. Replaced the new ice bucket in the freezer and filled it with the ice. Also replaced the water filter. The ice bucket repair was very easy and fast. Filter replacement took more time since I had to go buy some new tubing.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: JAMES A from Orlando, FL

Ice maker quit

i replace the IM3 with a upgrade to the IM6 ice maker. a simple swap and easy to install. with very good instructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6