2353273-1-S-GE-GXRTDR-In-Line Icemaker Filter
2353273-1-S-GE-GXRTDR-In-Line Icemaker Filter

In-Line Icemaker Filter

PartSelect Number PS2353273

This filter works only with plastic lines. It has a new design with quick connect fittings at the end of the filter.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $24.58
  • You Save

    $4.10
  • Your Price

    $20.48
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 6 reviews What's this?
1-6 of 6
 

22 of 29 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrank from Las Cruces NM

Ice make auger rusted, unable to serve clean ice.

Replacement auger and ice bucket assembly was perfect. Just had to remove the front door/flap assembly from the old unit and screw on to the new. The water filter kit took more time to read the box instructions than it did to install. Perfect. Am very pleased with the service/value offered by PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 13 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench set

CustomerKelly from Atlanta GA

Water dispenser not dispensing water

the back plate was removed and the solenoid part was removed for ordering. when installing, the same plate was removed. then the part was installed. also we put in an in-line water filter. that just included splicing the common inlet tube prior to the soloniod entrance and installing the filter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJane from San Dieg0 CA

Replacing filter and auger/ice bucket assembly

After I realized that I needed to take the front and door off the old ice bucket (which involved removing 4 screws) and mount it on the new part (putting in those 4 screws), the job was easy. Installing the new assembly requires shoving it into place without really being able to see how or where it attaches, so I wasn't sure it worked until it produced ice a few hours later, and it did.

The filter on the fridge was more than 10 years old, but the new GE Smart filter and its adapters screwed and snapped into place easily. Subsequent filter changes will be simple - just a snap!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLARRY from McGregor TX

Ice bucket auger was rusting and getting the ice dirty.

Removed the old ice bucket from the freezer and placed the ice in a plastic bag to reuse. Removed the ice bucket front cover by removing six (6) screws. Installed the old front cover to the new ice bucket by using four (4) screws. Replaced the new ice bucket in the freezer and filled it with the ice. Also replaced the water filter. The ice bucket repair was very easy and fast. Filter replacement took more time since I had to go buy some new tubing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerJAMES A from Orlando FL

Ice maker quit

i replace the IM3 with a upgrade to the IM6 ice maker. a simple swap and easy to install. with very good instructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 10 people found this instruction helpful

Parts Used

  • In-Line Icemaker Filter

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsWrench set

CustomerAllen from Port Ludlow, WA

After market ge water filter spud fitting broke off

It originally appeared that an easy out would be required to remove ferule from piping line, but later it became necessary to cut old broken fitting off and replace with compression fitting in replacement kit. Total time to repair after all tools were on hand (needed to buy tubing cuter) was about 45 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6