2351984-1-S-Whirlpool-W10111435-Bellow - Gray
2351984-1-S-Whirlpool-W10111435-Bellow - Gray 2351984-2-S-Whirlpool-W10111435-Bellow - Gray http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/TCQNS8DN.gif

Bellow - Gray

PartSelect Number PS2351984

Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $132.00
  • You Save

    $22.00
  • Your Price

    $110.00
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 8 reviews What's this?
1-5 of 8
 

128 of 148 people found this instruction helpful

Parts Used

  • Bellow - Gray

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerMarty from Belfair, WA

Water leak from bottom of door.

I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.

Help other customers find the most helpful instructions.

Were these instructions helpful?

43 of 45 people found this instruction helpful

Parts Used

  • Bellow - Gray

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerRobert from Charlotte, NC

My epic z is only three years old but started to leak at the bottom of the washer door for no obvious reason. Before replacing the bellow, I suggest you make sure the door latch is not loose and also make sure the star driver screws that secure the glass in the door are all snug (do not overtighten)

Since most people do not replace bellows for a living, I have great instructions for you to follow. I found the entire repair manual on the web.Just follow the repair instructions as written. Two other suggestions, use a very small amount of liquid diswasher soap to lubricate the bellow when fitting it over the washer drum assembly, makes life a lot easier. Second, get a second pair of hands to help you hold the bellow in place as you mount it or you will find yourself "chasing your tail". Bellow replacement and tightening the door and latch fixed the problem. Mom was happy :)...PS the buying experience from PartSelect , part delivery, speed was perfect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

28 of 41 people found this instruction helpful

Parts Used

  • Bellow - Gray

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRichard from Mount Pocono, PA

Bellow was cut on the bottom, leaked.

The top panel was removed, right side pulls out, left side has a lint drawer that pulls out exposing a phillips head screw. The bottom panel is removed by taking three screws out of the bottom, then the panel pulls down. Remove the additional screws (4) holding the door panel on. Loosen the band (phillipshead screw) holding the bellow on and pull the bellow off the channel. It also pulls off the door opening channel. Pull the new piece over the channels, tighten the band and reverse the removal procedure.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 15 people found this instruction helpful

Parts Used

  • Bellow - Gray

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerChristopher from Myrtle Beach, SC

Water leak

Remove outer retaining ring by pulling spring clip located at bottom of the seal. Push the bellows into the tub. Loosen the inner retaining ring clip (located on the left, facing the front of the machine) with a phillips screwdriver and guide the ring out. Remove the old bellows. Put in the new part with the tab on top and the drain holes on the bottom. Reinstall the rings. Kind of tedious but not complicated.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 11 people found this instruction helpful

Parts Used

  • Bellow - Gray

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRich from Los Altos, CA

Bellow was torn at the door causing water to leak

I would recommend to remove the front loader door first. Then remove the clamp that holds the front of the bellow to the washer, Remove the top panel and then the front panel. Remove the band that holds the back of the bellow to the washer. Reverse the process to install the bellow. It helps to apply a little soapy water to make it easy to put the bellow on the track for both the front and back. It also helps to have four hands. Hope you have a friend or significant other.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 8