2351821-1-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W
2351821-1-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W 2351821-2-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W http://www.partselect.com/Schematics/GE/GE_Thumb/00123223i01.gif

Halogen Light Bulb - 120V 20W

PartSelect Number PS2351821

Sold individually.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $7.03
  • You Save

    $1.17
  • Your Price

    $5.86
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 33 reviews What's this?
1-5 of 33
 

163 of 222 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerMark from GRAND BLANC, MI

Lens cracked and bulbs burned out

First I removed the single screw holding the lens assembly in place. Then I lowered the assembly and tilted it until it came out. To remove the existing cracked glass lens there were four tabs bent down on it. By hand I lifted each tab just enough to remove the broken lens. I then replaced the broken lens with the new one and re-bent the tabs down by hand to secure them to the new lens.

The lens assembly, now removed, revealed the cavity that contained the two halogen bulbs. Since they were both burned out for days, they weren't hot so I could pull each one out by hand. The bulbs are secured by two straight heavy gauge wire leads and provided a little resistance but come out fairly easily. Make a mental note of the angle they came out so it will be easier to replace them with new ones.

You're not supposed to touch halogen bulbs with your bare hands, so I used the bubble wrap they came in as a means to hold the bulb while installing it.

Be sure to insert the bulbs at the same angle they came out so the pins do not get bent.

Once both bulbs are in place, replace the lens cover assembly by putting the end opposite where the screw hole goes in first on the right, then swing it up until flush and screw it down.

Help other customers find the most helpful instructions.

Were these instructions helpful?

83 of 154 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerBarbara from Littleton, CO

None

I had no troubles!

Thank you...

Help other customers find the most helpful instructions.

Were these instructions helpful?

47 of 64 people found this instruction helpful

Parts Used

  • Halogen Light Bulb - 120V 20W

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerRobert from Naples, ME

Under the vent light bulbs needed to be replaced

Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!

Help other customers find the most helpful instructions.

Were these instructions helpful?

29 of 45 people found this instruction helpful

Parts Used

  • Halogen Light Bulb - 120V 20W

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerWalter from Midvale, UT

This lamp does not have easy access

This is the second time that this lamp hase gone out. It is located in a small space in the top of the microwave and you need to remove the top front pannel, then take a screw or two out of a metal shield and bend the shield up to get your hand into the compartment where, if you know how, you can reach in and lift out the reflector shield that the lighbulb is plugged into and remove the old one and plug in the new one. The first time was hard to figure out how to do it but the second time wasn't bad because I knew how to do it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 22 people found this instruction helpful

Parts Used

  • Halogen Light Bulb - 120V 20W

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerThomas from Wake Forest, NC

Halogen bulb burned out

*Remove Two Phillips head screws from the top of vent slide the vent left to remove it. Take the charcoal filter out then the metal cover underneath the filter. It also has a phillips head screw. bulb socket is on right facing down. Squeeze the metal clips and remove socket from bracket. Installation is the reverse of removal.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 33