2351821-1-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W
2351821-1-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W 2351821-2-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W http://www.partselect.com/Schematics/GE/00125324i01.gif

Halogen Light Bulb - 120V 20W

PartSelect Number PS2351821

Sold individually.

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $7.63
  • You Save

    $1.27
  • Your Price

    $6.36
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 33 reviews What's this?
 

11 of 15 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: A Bit Difficult
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Jerry from Rio Vista, CA

Two counter light bulbs burned out

After removing the screws holding the 2 cover plates in position, I removed the halogen light bulbs with my fingers. Then I placed a paper towel around the first replacement bulb and lined up the two wire connectors with the two holes in the receptacle. I pushed in, but the bulb's probes did not slide into the receptacle. I spent five minutes aligning and pushing but to no avail. Then I removed the filter screen on the side of the receptacle, shined a flashlight beam on the receptacle, and with an improved view of the two holes in the receptacle, slid the bulb in. The second bulb was inserted in a few minutes, and the job was done. Whoever designed the halogen bulb was not as bright as Thomas Edison.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Robert D. from Knoxville, TN

The plastic kickplate which conceals the evaporator coils had broken one of the four plastic snap-in connectors, allowing the kickplate to droop down upon the right side creating an unsightly appliance appearence.

Although a fine refigerator from a performance standpoint, a drooping evaporator coil kickplate created an unsightly appearence as result of a broken snap-in plastic connector. The repair should have been fairly simple, merely requiring the removal of the old plastic kickplate by depressing the plastic connectors upon each end to release the original kickplate, followed by snapping the new kickplate into position at most, a five minute repair. However, although the replacement kickplate I received from PartSelect for $58.67 (plus shipping), does contain all four plastic snap-in connectors as required, the replacement kickplate had not been molded to rest flat upon the front refrigerator trim, properly concealing the evaporator coils (as the original kickplate mounted prior to sustaining a broken snap-in connector). However, after replacing this plastic kickplate, my refrigerator continues to suffer from a pitiful, drooping kickplate upon one end. Although PartSelect has always come through for me upon previous repair part orders, in this case the better choice would have been to dismissed my desire for retaining the factory appearence of this expensive appliance, and simply apply adhesive to the original kickplate instead.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: John from ORLANDO, FL

The halogen light above the stovetop burned out

the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Bryan from South Beach, OR

Light for cooktop burned out

Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Robert L. from Racine, WI

Lamp burnt out

We had our kitchen remodeled; new cabinets, countertop, range, refigerator, microwave, dishwasher and floor.

The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.

A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.

The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!

Bob
Racine, WI

Help other customers find the most helpful instructions.

Were these instructions helpful?