Quick Question!

Have you ever purchased from PartSelect.com before?

2351821-1-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W
2351821-1-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W 2351821-2-S-GE-WB25X10019-Halogen Light Bulb - 120V 20W http://www.partselect.com/Schematics/GE/00125324i01.gif

Halogen Light Bulb - 120V 20W

Compare At

$7.43

You Save

$1.24

Your Price

$6.19
Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2351821
Manufacturer Part Number WB25X10019
Manufactured by GE

This lightbulb is located on the inside of your microwave. The bulb is behind the top grill. It will need to be replaced when it has burnt out and no longer works. Unplug the unit. Remove the top grill of your microwave, use your screwdriver to open the light socket, scrape off any silicone holding the bulb in place, clean the area of any oil and dirt, insert the new bulb into the socket without touching the bulb, slide the holder back into place, line up the tabs on top of the metal plate, and secure the holder back into place.

This part works with the following brands: General Electric, Kenmore, Hotpoint.

This part works with the following products: Microwave, Microwave Oven Combo.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Recent

Question:

So I donnot like purchasing things online but the light inside my convection oven went out and I wanted to buy a new one. I went to the local home hardware store and they recommended me this 50W bulb but when I was online I was told to use a 20W bulb. Is the 50W bulb safe to use in the conv. oven?

Maya
Answer:

Hello Maya, your model is designed to use a 20W bulb. With that said we recommend not going over this wattage as it is the maximum for your model. I hope this helps!

2 people found this helpful.
Question:

How do I remove the light cover over my range??

Steve
Answer:

Hi Steve, to remove the cover all you will need is a Phillips head screwdriver. Once the screw is out, the light cover should easily open. Best of luck with this repair!

1 person found this helpful.

Most Helpful

Question:

I don’t know how to do this installation... I know where the light is but its covered and I don’t want to break it

Anna
Answer:

Hi Anna, the light cover should easily just pop off, and from there you should be able to change the bulb. If you are not able to pry the light cover off, check if there are any fasteners holding it in place, and remove those. If you are still not able to remove it, you may need to replace the light assembly WP74009970. Please let us know if you have any further questions.

2 people found this helpful.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 35 reviews What's this?
1-15 of 35
 

203 of 277 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Mark from GRAND BLANC, MI

Lens cracked and bulbs burned out

First I removed the single screw holding the lens assembly in place. Then I lowered the assembly and tilted it until it came out. To remove the existing cracked glass lens there were four tabs bent down on it. By hand I lifted each tab just enough to remove the broken lens. I then replaced the broken lens with the new one and re-bent the tabs down by hand to secure them to the new lens.

The lens assembly, now removed, revealed the cavity that contained the two halogen bulbs. Since they were both burned out for days, they weren't hot so I could pull each one out by hand. The bulbs are secured by two straight heavy gauge wire leads and provided a little resistance but come out fairly easily. Make a mental note of the angle they came out so it will be easier to replace them with new ones.

You're not supposed to touch halogen bulbs with your bare hands, so I used the bubble wrap they came in as a means to hold the bulb while installing it.

Be sure to insert the bulbs at the same angle they came out so the pins do not get bent.

Once both bulbs are in place, replace the lens cover assembly by putting the end opposite where the screw hole goes in first on the right, then swing it up until flush and screw it down.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

85 of 161 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Barbara from Littleton, CO

None

I had no troubles!

Thank you...

Help other customers find the most helpful instructions.

Were these instructions helpful?   

55 of 75 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Robert from Naples, ME

Under the vent light bulbs needed to be replaced

Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

30 of 48 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Walter from Midvale, UT

This lamp does not have easy access

This is the second time that this lamp hase gone out. It is located in a small space in the top of the microwave and you need to remove the top front pannel, then take a screw or two out of a metal shield and bend the shield up to get your hand into the compartment where, if you know how, you can reach in and lift out the reflector shield that the lighbulb is plugged into and remove the old one and plug in the new one. The first time was hard to figure out how to do it but the second time wasn't bad because I knew how to do it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

22 of 27 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Wake Forest, NC

Halogen bulb burned out

*Remove Two Phillips head screws from the top of vent slide the vent left to remove it. Take the charcoal filter out then the metal cover underneath the filter. It also has a phillips head screw. bulb socket is on right facing down. Squeeze the metal clips and remove socket from bracket. Installation is the reverse of removal.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 19 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: A Bit Difficult
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Jerry from Rio Vista, CA

Two counter light bulbs burned out

After removing the screws holding the 2 cover plates in position, I removed the halogen light bulbs with my fingers. Then I placed a paper towel around the first replacement bulb and lined up the two wire connectors with the two holes in the receptacle. I pushed in, but the bulb's probes did not slide into the receptacle. I spent five minutes aligning and pushing but to no avail. Then I removed the filter screen on the side of the receptacle, shined a flashlight beam on the receptacle, and with an improved view of the two holes in the receptacle, slid the bulb in. The second bulb was inserted in a few minutes, and the job was done. Whoever designed the halogen bulb was not as bright as Thomas Edison.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 11 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: John from ORLANDO, FL

The halogen light above the stovetop burned out

the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Robert D. from Knoxville, TN

The plastic kickplate which conceals the evaporator coils had broken one of the four plastic snap-in connectors, allowing the kickplate to droop down upon the right side creating an unsightly appliance appearence.

Although a fine refigerator from a performance standpoint, a drooping evaporator coil kickplate created an unsightly appearence as result of a broken snap-in plastic connector. The repair should have been fairly simple, merely requiring the removal of the old plastic kickplate by depressing the plastic connectors upon each end to release the original kickplate, followed by snapping the new kickplate into position at most, a five minute repair. However, although the replacement kickplate I received from PartSelect for $58.67 (plus shipping), does contain all four plastic snap-in connectors as required, the replacement kickplate had not been molded to rest flat upon the front refrigerator trim, properly concealing the evaporator coils (as the original kickplate mounted prior to sustaining a broken snap-in connector). However, after replacing this plastic kickplate, my refrigerator continues to suffer from a pitiful, drooping kickplate upon one end. Although PartSelect has always come through for me upon previous repair part orders, in this case the better choice would have been to dismissed my desire for retaining the factory appearence of this expensive appliance, and simply apply adhesive to the original kickplate instead.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Bryan from South Beach, OR

Light for cooktop burned out

Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Robert L. from Racine, WI

Lamp burnt out

We had our kitchen remodeled; new cabinets, countertop, range, refigerator, microwave, dishwasher and floor.

The cabinets around the microwave were custom made; it looks great but it hid the screws, which had to be unscrewed to remove the grill so the interior light of the microwave could be replaced.

A stand was used to support the microwave as I lowered it so the screws could exposed so the light could be replaced.

The light was replaced, the microwave was raised back into place and all is well. I replaced the bulb while my wife was out of town. When she returned she noticed that the microwave was nice and clean; she was NOT aware of the fact that the bulb was replaced!

Bob
Racine, WI

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: pete from roslyn, NY

Both undercabinet light bulbs blown

1. Open the cover over light bulbs with screwdriver.
2. Pulled out blown bulbs.
3. Inserts new bulbs from Partselect.
4. Tested new bulbs
5. Closed the cover over light bulbs with scvrewdriver.
6. Threw out old bulbs and packaging material.

Now, was that easy or what!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Darren from Madison, CT

Halogen light for the microwave above the stove went out.

Ordered the part. 2 days later part arrives. Took me 30 seconds to install the part. Sorry it was not more eventful.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Don from Wildwood, MO

Halogen lamps needed replacement

Easy to repair. One screw, remove bulbs, replace with new ones, secure screw.

Partselect.com shipped items quickly as promised, provided follow up email confirming receipt of order, a second email confirming shipment & a link to check shipping status.

Would not hesitate to do business with Partselect.com again!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: James from Sandown, NH

Latch broke,bulb out

followed instructions posted on line.very good service .parts arrived in a speedy manner and were a perfect fit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Halogen Light Bulb - 120V 20W
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Screw drivers
Customer: Gregory from Gastonia, NC

Lamp burned out.

Removed one screw, removed cover, and replaced lamp. Pretty straightforward.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 35

Model Cross Reference

This part works with the following models:

PartSelect Number: PS2351821
Manufacturer Part Number: WB25X10019
Brand Model Number Description
Kenmore36363672200Microwave
Kenmore36363672201Microwave
Kenmore36363673200Microwave
Kenmore36363674200Microwave
Kenmore36363674201Microwave
Kenmore36363679200Microwave
Kenmore36363679201Microwave
Kenmore36363692301Microwave
Kenmore36363692302Microwave
Kenmore36363693301Microwave
Kenmore36363693302Microwave
Kenmore36363694301Microwave
Kenmore36363694302Microwave
Kenmore36363699301Microwave
Kenmore36363699302Microwave
HotpointCSA1201RSS01Microwave
HotpointCSA1201RSS02Microwave
HotpointCSA1201RSS03Microwave
General ElectricCVM1790SS1SSMicrowave
General ElectricCVM1790SS2SSMicrowave
General ElectricCVM2072SM1SSMicrowave
General ElectricCVM2072SM2SSMicrowave
General ElectricCVM2072SM3SSMicrowave
General ElectricCVM2072SM4SSMicrowave
General ElectricDVM1850DM2BBMicrowave
General ElectricDVM1850DM2WWMicrowave
General ElectricDVM1850DM3BBMicrowave
General ElectricDVM1850DM3WWMicrowave
General ElectricDVM1850DM4BBMicrowave
General ElectricDVM1850DM4WWMicrowave