Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS235170
This part establishes and maintains the internal temperature of the oven cavity.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Check the switch with an ohm meter, 0 resistance in the closed position = a bad switch. I went to the web site found the part. ordered it next day it shows up. Removed the pot grids and all control knobs for the burners and oven lifted the top of the stove up, and off. I removed face plate behind the control knobs 3 screws, I removed the 2 screws holding the oven switch. opened the oven and un cliped the thermostat wire from the back wall. Uncoiled new wire feed under the burner shield to the back of the unit and back down the old hole cliped in the new wire. put the 2 screws into the new switch and re-assembled the rest in the reverse order i took it off . all this while watching my 11 month old grandaughter.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Checked switch using test meter and found voltage going in but no voltage out when switch was turned on. Removed all burner knobs, raised top cover and disconnected two wires from thermostat switch. Removed the thermostat probe from oven interior by pushing it through hole in top. Removed two screws holding switch and pulled out entire assembly. Used a wire coat hanger pushed through hole for probe so I could see where to fish the probe into the oven. Hooked up electrical connections and tested. Everything worked well.Received part from Partselect in one business day. Excellent service and response.
The repair was fairly easy, you take off all the burner knobs there are small screws on the face of the cover panel and a few on the bottom That come off the cover panel should come off after you remove the screws and the switch for the oven light the wires just clip on the switch there are two .the thermostat is held on by two small screws that are on the cover panel.you lift up the burner panel you have room to feed the thermostat wire in the stove,there is a small hole in the back were you feed the wire through then the metal part is held in place by two small clips that are in the oven on the back wall.I didnt have to trouble shoot becase I knew what part I needed because it was broken,It was a fairly easy repair hopefully this is helpful Good Luck
Once I figured out how to get the top off it was not too bad. all of the screws and igniters for the burners had to be removed. The actual install of the thermostat was simple after that. The igniter was also an easy install. Overall, it takes more time to disassemble the stove to get to the problem than to install the part.
I had to open the top of the gas range and remove the front panel where the knobs are. I was able to identify where the thermostat wire went. I had a little trouble figuring out how to thread the thermostat wire into the back of the range but then I poked the old thermostat through the hole from the inside so I could tell where it went. I just had to put all the screw back in and check it and it worked fine.
My Hotpoint gas oven became extremely hot after using it . Only after unplugging the electrical cord, turned it off. Replacing the control valve (thermostat) solved the problem. The stove top had to be pried up with a flat screw driver then propped up. Prying off the oven control valve revealed two mounting screws (philips head). Next remove thermostat sensor bulb inside oven at back wall. Remove old thermostat control and bulb assembly. Installation is reverse order of disassembly.
The R&R of the defective thermostat was at first look relatively simple. The job was made more complicated because in order to remove the old thermostat and then route the new thermostat across the top of the stove, under the burners, and down through a small hole into the oven space I had to remove the whole top of the stove. This process is not hard, just time consuming. Be very careful of razor sharp edges, they make you bleed. The final calibration of the oven is an easy adjustment in the oven knob. All in all it was an good experience. Lyle Nelson
I removed all the burner heads with a torx driver & released the top of the stove by pushing in two clips with a screwdriver. I raised the top and located the thermostat as it fed through back of stove, then tied a line to the old thermostat to be used to pull the new one through. This did not work, so I removed a cover on the back of stove to provide more room & spread insulation apart so i could see hole. I was able to easily feed new thermostat through hole and reassemble.
1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.
To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."
The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!
My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.