http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/33508.gif
See part 29 in the diagram

Clear Belt

PartSelect Number PS2347264

The parts specs are: 25 3/8" long and 1/4" wide.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not draining.
  • Noisy.
  • Not cleaning dishes properly.
  • Compare At

    $25.57
  • You Save

    $4.26
  • Your Price

    $21.31
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 26 reviews What's this?
1-15 of 26
 

20 of 25 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerTheodore from Madison CT

Dishes not being washed, water below heater element

I attempted to fix it about a year ago. Took apart the screen center stem and water spinner.
I could not find anything wrong. The machine was used very infrequently over the years. Recently my wife approached me again to fix it and knowing I didn't find any thing the first time: I took the lower panel strip off and found the translucent belt broken. I found your site matched up a belt size and ordered it. Three days later it arrived, I installed it and everything seems to work. The water drains and I'm back in business. It was so easy I was embarrassed I did not fix it the first time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 20 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerGregory T. from Pittsburgh PA

Noticed a water growing water spot downstairs under the dishwasher .

I pulled the dishwasher out & watch it complete 1 cycle : water was leaking at a through hole used to secure the upper dish rack roller to the cabinet : the nut & seal holding the roller was loose allowing water to drip down the outside of the cabinet under the insulation.: water dripped onto the belt causing belt to slip : many water marks around the pump ; as a precaution i replaced the pump bottom seal & the pump to chassis gasket : I also checked the other 3 rolles ; replaced cracked top flange & installed a more flexable water supply hose .

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

Customerjames from smithtown NY

Belt broken, dirty water remaining in washer

I had already loosened the motor from inside the tub....so it was fairly easy to wrap the new belt around the motor/pulley system.... even though the old broken belt was 2 inches longer than the new belt(probably as a result of age and use, but the new belt is obviously the right size!) Once in place, I did have to take some care in screwing down the seal from inside being as it wanted to go more to one side than the other from the pressure of the tight belt, but all in all, it wasn't so bad. Unfortunately for me when I put the dishwasher on, I thought the dirty water problem would go away, but I soon learned that I also had a clog in the plumbing. I guess I'll never know if one thing caused the other or it was just 2 things going wrong at the same exact time. But everything is perfect now. Also, the part I ordered was at my doorstep in less than 36 hours!!!! That's fantastic!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerPaul from Piedmont CA

No spray-arm motion, no drainage (broken belt)

Getting the new belt installed is a bit tricky; it seems too small to span the pump and drive pulleys.

Nevertheless, start with the belt positioned in the drive pulley and stretch it so one side fits into the slot of the pump pulley. Using both hands, crank the pulley over until the belt "rolls" into place. It may take several tries as the workspace tends to be rather tight. Good luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyA Bit Difficult

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMichael from Bethany CT

Broken drive belt

First I was amazed that the belt was available for my ancient dishwasher. Then I was amazed again when it came overnight. The instructions said to stretch it over the two pulleys but my hands weren't strong enough. In a sudden flash of brilliance I decided to use a screwdriver as a lever to force it onto the second pulley. Done deal - happy home handyman.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerThanh from Matthews AL

Water not drained

Remove bottom cover.
Put the belt on the large pulley and stretch it about 5 times to make it larger. Remove the belt from the large pulley and put it on the small pulley at the motor. Stretch it to left side of the large pulley and make sure the belt is on partial of the pulley's groove then rotate the large pulley forward. The pulley will pull the belt into the groove by itself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRichard from Houston TX

Broken drive belt

No problem at all. Belt slipped on very easily. Followed directions in the package.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerJason from Sunnyvale CA

Belt broken, dishwasher didn't drain

Belt seemed too small at first to fit, but turning the power module pulley while holding the belt enabled it to slip in properly. Didn't help that there's not much space to work.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRafael from Porter Ranch CA

The drive belt was too old and it broke. It was not draining the water inside the dishwasher.

I opened the bottom part of the dishwasher, from there you can see all parts of the motor including the pulleys where the broken belt came from. From here, I took the new belt, placed some silicon all around it and installed it by rotating the pulleys clockwise until the belt wraps around it.
Then I tested it by turning the control on the Wash/Rinse mode and it started to drain the water right away.
DONE!

NO PROBLEM!!!

PS.
THANK YOU FOR DELIVERING IT ON TIME.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyVery Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerCatherine from Spring Grove MN

Belt was worn out

I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDanny W. from Celina TN

Belt slipping after 23 years of use

Removed bottom front panel with nutdriver,rolled old belt off rolled new belt on and applied belt grease that came with new belt.New belt came with instructions that were exactly right for belt installation. Thank You Danny Hammons

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerjames from whitestone NY

Broken belt

Took off bottom cover. Put belt on center housing than put belt on moter pully.Rolled belt down onto center pully while turning pully clockwise. Popped right on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsWrench set, Wrench(Adjustable)

CustomerKelly from Forty Fort PA

Broken belt

This was a pain to change due to very limited access. Also belt had very little stretch. Had to really put some thought in it before attempting.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyDifficult

Time to do repair:30 - 60 mins

Tools

CustomerRichard from Rockledge FL

Broken dishwasher belt

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Clear Belt

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench set

CustomerROBERT from COLLINSVILLE IL

Would'nt pump the water out

Had to loosen the drive motor enough to slip the belt around the pulleys. The only problem was the amount of space available to work in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 26