2347253-1-S-Whirlpool-6-3033630-Idler Pulley Arm
2347253-1-S-Whirlpool-6-3033630-Idler Pulley Arm 2347253-2-S-Whirlpool-6-3033630-Idler Pulley Arm

Idler Pulley Arm

PartSelect Number PS2347253

Manufacturer Part Number 6-3033630
Manufactured by Whirlpool

A dryer's idler pulley wheel serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Compare At

    $18.84
  • You Save

    $3.14
  • Your Price

    $15.70
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Idler Pulley Wheel

Part Number 2347254

This part is used to help the belt to rotate the drum.

$11.63
In Stock

Idler Arm Screw Sleeve

Part Number 2032615

This part is intended for use with the screw that holds the idler pulley on your clothes dryer.

$18.71
In Stock

Idler Bracket Spacer

Part Number 2177475

$17.55
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

10 of 12 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

Customeradriel from sylmar CA

Original problem: Blower fan came loose from the motor shaft.Belt and was making a noise clothes were slow drying. Second problem appear upon inspection: Idler pulley bracket shaft severely worn.

Replacing the blower fan took way too long, like 4 hrs, because I didn't know how to disassemble the dryer and get to the problem. Replacing the idler bracket and assorted retaining rings and washers was fast, something like 1 hour. Disconnect the power cord, exhaust hose, and gas line. Remove two screws at the bottom of the face of the machine, unplug the electrical harness to the door light, switch and ground and remove the front of the machine. Remove the access panel at the back of the machine and remove the belt from the idler pulley. Remove the four screws holding the front drum support assembly and remove the drum. Replace some old retaining rings and the spring washers on the drum support rollers. Around back assemble the idler pulley assembly with some new washers and the old roller which seemed in good condition. Put it all back together. About one hour.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 11 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerJeffrey from Gloucester VA

Sqeeky / sqealing dryer

Took off face of dryer (two lower screws below door in front) and then removed the drum which gave me access to the idler arm and idler pully. Vaccumed the interior to remove dust and lint. Replaced idler arm and idler pulley assembly. Replace old belt as drum was reinstalled. Opened rear access panel to complete final routing of the new belt over idler pulley and drive motor. Turned the machine on to check repairs and function. Closed rear access door. Pushed dryer back into place and re-leveled machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerStephen from Crawfordsville IN

Broken belt

There were two screws to remove the front of the dryer. Then 4 screws to remove the front drum support. Remove the drum. Then one nut each on changing the back drum support rollers. Assemble the drum and front support in reverse, and door front, don't forget to put the new drive belt ovre the drum. Then from the rear panel opening, one screw to change the idler assembly. Easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerOrson from Harrisburg IL

Horrible squeaking when running

I did it exactly the way the video showed it. I thought I would have to take it out to the pole barn and spend 5-6 hours on it. Because of the excellent video, it was much easier than I thougt it would be.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4