2347234-1-S-Whirlpool-6-2022030-Drain Pump
2347234-1-S-Whirlpool-6-2022030-Drain Pump 2347234-2-S-Whirlpool-6-2022030-Drain Pump 2347234-3-S-Whirlpool-6-2022030-Drain Pump http://www.partselect.com/Schematics/Maytag/37313.gif

Drain Pump

PartSelect Number PS2347234

This assembly uses 2 belts. Order belts if you notice wear and tear.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Leaking.
  • Noisy.
  • Pumps but will not spin.
  • Burning smell.
  • Compare At

    $94.66
  • You Save

    $15.78
  • Your Price

    $78.88
Special Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Belt Kit

Part Number 2005284

This kit includes both the drive belt and the pump belt which are both "V" shaped.

$23.73
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 17 reviews What's this?
 

8 of 9 people found this instruction helpful

Parts Used:
  • Drain Pump
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: richard from Tarzana, CA

Water leak

Tilted the washing machine back at 45 degree angle. Removed three screws from the underside of machine. Slipped belt off pump. Lessened two hose clamps and removed hoses.
Lifted old pump out. Dropped new pump in place.
Screwed in the 3 screws. Slipped on the belt.
Attached two hoses. Tightened hose clamps.
Set washing machine upright.

No more leak.
My problem was I could not prove the pump was the source, but after switching it out I have had no problems (good enough).

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used:
  • Drain Pump
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set
Customer: Basil from St. Charles, MO

Washer did not drain.

Took front panel off. Ran machine. Pump is see-through. Could not see any "aeration" of the water in the pump and no water was coming out of drain hose. Disconnected electric. Disconnected hose from drum to pump(first emptied ALL water from drom)and drained in bucket. Disconnected drain hose from pump to drain and drained any water. Checked for obstructions in hoses. Removed pump. Checked belt (was fine after 14 years). Ordered new pump. Received the next day! Replaced pump and tighten belt. Connected hoses and test it. All OK. Replace panel and did laundry.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used:
  • Drain Pump
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: James from Baton Rouge, LA

Standing water in washer tub

Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used:
  • Drain Pump
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Steve from Martinsville, IN

All water into tub leaked from bottom of machine

To troubleshoot the problem I removed a panel/blank from the back of the machine. I then started to fill the tub while watching the pump. It immediately leaked from the shaft seal. I ordered the part early the next morning. It arrived late the next day. I was able to remove the front panel of the machine by removing a screw at each front corner of the bottom of the machine. The pump was attached with three screws which were simple to remove. The pump was an exact replacement and fit identically to the original. I tensioned the belt, and tested the machine. Before reinstalling the front cover, I cleaned the interior of the machine a bit and replaced a couple of hose clamps whose steel screws had started to corrode. All in all a simple repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Charles from Chalfont, PA

Washer was not draining completely & at times a small amount of water would leak from under the washer.

Followed the instructions on-line. Pulled the washer out from the wall, tipped it back about 45 deg. & removed the two philips screws as the base of the front of the washer.Removed the old belts which showed little wear, disconnected the hoses from the pump. Replaced the pump which was held in by only 3 nut-head screws, attached the belts & adjusted the tesnion as described on the website.

Help other customers find the most helpful instructions.

Were these instructions helpful?