2347231-1-M-Whirlpool-6-2008160-Motor-Pulley.jpg
2347231-1-S-Whirlpool-6-2008160-Motor-Pulley.jpg 2347231-2-S-Whirlpool-6-2008160-Motor-Pulley.jpg

Motor Pulley

PartSelect Number PS2347231

This helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Unusual Noise.
  • Compare At

    $27.86
  • You Save

    $4.64
  • Your Price

    $23.22
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 4 reviews What's this?
1-4 of 4
 

12 of 16 people found this instruction helpful

Parts Used

  • Motor Pulley

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsWrench(Adjustable)

CustomerRobert from Menomonee Falls WI

The water didn't pump out during the spin cycle

I took out the two screws in the bottom front panel of the washer, and rotated the front panel from the bottom away from the machine until the top or the panel was released from the machine frame. I then tilted the washer back to get access to the bottom of the machine. The pump pulley had split in half, and the bottom half fell off the drive motor shaft. The only problem I had was breaking free the set screw that holds the pulley to the drive motor shaft. I used a long arm Allen wrench and an adjustable "Cresent" wrench to apply enough force to break the set screw loose. Iclamped the upper transmission belts tightly to keep the motor shaft from turning while I loosened the set screw.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerFranz from Lakeland FL

No water drain

removed old pully, put new one on with hex driver, removed belts, put new belts on and finished.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

Tools

CustomerPeter from Westhampton Beach NY

Pulley came apart , frayed belt.

Tilted washer on its side.Took off old pulley- Allen wrench. Slipped on new pulley and replaced both the drive belt and pump belt. Works like new again- maybe for another 29 years!!! ???

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

  • Motor Pulley

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerXuanbao from Norwalk CA

The washing machine ran noisily

Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4