2347193-1-S-Whirlpool-35-6780-Drain Pump
2347193-1-S-Whirlpool-35-6780-Drain Pump 2347193-2-S-Whirlpool-35-6780-Drain Pump http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/55028.gif

Drain Pump

PartSelect Number PS2347193

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Will not drain.
  • Leaking.
  • Burning smell.
  • Pumps but will not spin.
  • Will not agitate.
  • Will Not Start.
  • Shakes and moves.
  • Compare At

    $79.28
  • You Save

    $13.21
  • Your Price

    $66.07
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 39 reviews What's this?
1-5 of 39
 

202 of 215 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Socket set

CustomerRanse from Layton, UT

Pump was making a grinding noise

The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

100 of 111 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

Customerkevin from rochester, NY

Bearing on water pump siezed

back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

48 of 48 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Mesa, AZ

Skreeching noise during spin cycle

Pulled out washer, laid on front, removed access panel and the pump was right there. Three screws with 5/16" nut driver, pliers to release hose clamps, remove hoses, remove belt from pully, remove old pump. Install new pump with three screws, two hoses and clamps, finally put belt on new pulley and other small pulley and used screw driver shaft to pull belt on to large pulley. replace access panel, put washer back in place. It literally took me more time to clean the floor under where the washer was than to change the part. Piece-o'-cake.

Help other customers find the most helpful instructions.

Were these instructions helpful?

44 of 49 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerKathy from Wellington, KS

The bearing had some kind of metal (couragated) piece that worked it's way loose and was hanging up on the pump housing or retaing plate.

Removed the old pump,- disconetced the two hoses, and 3 retaining screws, sliped off the drive belt,. installed the new pump! simple!

Help other customers find the most helpful instructions.

Were these instructions helpful?

29 of 29 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerEsther from Big Run, PA

Bad water pump

shut off supply lines, remove cover on back of washer, remove drain hose from pump,inlet and exit. remove belt underneath washer from pump. remove 3 assembly screws. remove pump. set new pump in place. rescrew pump to washer. reatach inlet and exit hoses to pump put belt back on under washer put cover back on back of washer. turn supply flines back on. should work like new

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 39