2347193-1-M-Whirlpool-35-6780-Drain-Pump.jpg
2347193-1-S-Whirlpool-35-6780-Drain-Pump.jpg 2347193-2-S-Whirlpool-35-6780-Drain-Pump.jpg

Drain Pump

PartSelect Number PS2347193

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not drain.
  • Leaking water.
  • Burning smell.
  • Pumps but will not spin.
  • Will not agitate.
  • Will not start.
  • Shakes and moves.
  • Compare At

    $83.64
  • You Save

    $13.94
  • Your Price

    $69.70
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 27 reviews What's this?
1-15 of 27
 

53 of 55 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

Customerkevin from rochester NY

Bearing on water pump siezed

back panel,belt two hoses,three screws, $100 dollars for the part!! pump is a molded part with a bearing insertion, is made in USA ! I'm guessing around 7 to 10 dollar manufacturing cost. I'm thinking that kind of mark-up is only exceded by the pharmacutical industry. I'm looking to buy a used machine for parts!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 17 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Mesa AZ

Skreeching noise during spin cycle

Pulled out washer, laid on front, removed access panel and the pump was right there. Three screws with 5/16" nut driver, pliers to release hose clamps, remove hoses, remove belt from pully, remove old pump. Install new pump with three screws, two hoses and clamps, finally put belt on new pulley and other small pulley and used screw driver shaft to pull belt on to large pulley. replace access panel, put washer back in place. It literally took me more time to clean the floor under where the washer was than to change the part. Piece-o'-cake.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 12 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerEsther from Big Run PA

Bad water pump

shut off supply lines, remove cover on back of washer, remove drain hose from pump,inlet and exit. remove belt underneath washer from pump. remove 3 assembly screws. remove pump. set new pump in place. rescrew pump to washer. reatach inlet and exit hoses to pump put belt back on under washer put cover back on back of washer. turn supply flines back on. should work like new

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 11 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerPatrick from Accord NY

Loud hi pitched squeeling noise all the time.

Remove front panel and back service panel below water conn. lines. Put a 4" plastic box between the tub and inside of cabinet "directly opposite the spring to be removed to lower the tub to base for less opposing travel to unlatch spring from tub hook. Also took an old slotted screw driver w/ a blade about 1/4 " and grinded 1/8 from middle about an1/8" deep and used it to latch the spring when pushing it up and off the tub. Replaced all 6. Also did motor pivot spring. Tested and the it worked for one cycle, then the tub again just falls to the right as if the spring at 9 o'clock was broke and strains the belt drive but the spin cycle still works o.k. and the washer does not bang and walk away till you stop the machine. Thought the 6 tub springs would take care of both problems. Told that the snubber ring needs to be replaced. Never but another maytag again. JUst did the belt,a week later the water pump went then the springs.....

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerRichard from San Antonio TX

Bearings on the water pump self-destructed.

I tipped the washing machine back to allow me access to the bottom of the washing machine to remove the belt from the water pump. After removing the belt, I righted the machine, unscrewed the three screws holding the rear access panel on. I used pliers to remove the clamps from the inlet and outlet hoses then removed the hoses. I removed three screws holding the water pump on to the bottom panel of the washing machine. I removed the pump and replaced it with the new pump. I then reinstalled the screws, the hoses, the clamps, the access panel, and the belt. I plugged the washer back in and - viola! It works again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

CustomerMatthew from DOUGLASSVILLE PA

Washer made awful grinding sound then quit spinning

I took the bad water pump off installed the new one and hooked up the new drive belt. Overall it took me twenty minutes, not all that hard to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Socket set

CustomerCHERYL from HUDSON NH

Noise during spin cycle

Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orientation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerDale from Benton LA

The timer would quit in mid cycle. Spin did not drain the water in permanent press or delicate cycles.

I opened the front of the machine. The clips had rusted. One broke and the others were very difficult to work with. I pried the panel open with a large screwdriver. I took the back panel off to access the water pump. I removed the back panel on the electricals to access the timer. To replace the timer I pried off the decorative cover. To get the knob off you have to squeeze in on the timer split shaft while pulling out on the know. This was the second hardest part. (The front panel access was the most difficult). After that the timer clip is easy to loosen and it slides a littel then pops out. Electrical connection was obvious. The motor sping was the next most difficlt part. The spring fits on the rear part of the motor which is most easily accessed through the rear panel used for replacing the water pump. The water pump has three screws holding it and two hose clamps that come off easily with a pair of pliers. Before removing the water pump, I had to tip up the machine and take the belt off. This was also pretty easy. Put it back together and works great again on all cycles.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerBill from Mount Pleasant MI

Original factory water pump bearing seized up

Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerSteven from Commerce TX

Loud noise durring spin cycle

I removed the plate at lower left corner on rear of washer 3 screws and it pops right off after that there are 2 clamps on the hoses attached to the pump I removed those with pliers then I removed the 3 screws holding the pump to the bottom of the washer then pulled the pump through the hole and replaced it with the new pump installed all the screws then layed washer on its side and replaced the belt set it up pluged it in and no more noise sounds better than new. Thank you Part Select for making it an easy painless task to get the parts I needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerStuart from Erskine MN

Squeeling noise at the end of the spin cycle. Not all of water is spun out. Clothes still wet.

My Maytag Atlantis MAV7550AWW does not have a side inspection door like many have posted. After taking most of the washing machine apart I noticed in the front between the top lid and the main body there appeared what looked like some type of clips. I used a butter knife and pushed the V clip back and the one side of the top lid was released. After doing the other clip it was clear that was how to access the motor etc. After the top was open, it's hinged by a plastic hinge, you will need a small wrench and have to move the tub to the side to take off two small nuts also in the front. 8mm I think. Then the entire front of the machine comes off and the pump was right there. Time to remove and install the new pump was 15 minutes. I replaced the belt at this time also but had to lay the washer on it's side. Put the belt on two of the pulleys and pull hard. You will see that one of them is a spring held tightener. I did this outside on the deck as you will have water in the hoses and pump. After all was hooked up I ran a wash cycle only to hear that screeching sound was still there. My best guess is that it's a tub motor going. I am just going to use the washer till it dies then get a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers

CustomerDebbie from Colchester CT

Water intermittently leaking from bottom of washer

I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerInes from West Babylon NY

Machine making a grinding noise during spin cycle

On this particular model #MAV7550AWW Maytag washer, you do not remove a back panel since it is a three sided case. I first disconnected power and hoses from wall. Removed the belt from under the machine (you need to tilt the machine). To access the water pump you need to remove the front panel by first sliding a putty knife between the top of the machine and the panel slide it in about 2 inches from the edge to release the latch, repeat the procedure on the other side. On the inside or the panel about 2 inches there is a nut on either side once you remove both the front panel unlatches easily, from the bottom two latches. The water pump is located on the right front of the bottom plate. it is held in by three nut screws, (have plenty of towels to catch the water that is released once you disconnect the two hoses that are on the pump. The replacement part (made in the USA) is all plastic but fits perfectly. We Replaced the pump and reconnected everything. There is a video here on this site the explains in detail the removal and placement of the drive belt. The job is very simple to do. I am a woman under 5ft and I did this repair with the help of my son (17yr old). The machine is good as new. Second repair I have done on the machine and with a lot of savings!.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerEd from Adamsville TN

During the first rinse cycle, a loud metal to metal grinding sound occured. I shut down the machine and inspected thebottom of the washed and found the water pump hard to move. Obviously there was a problem.

I simply emptied the machine of all the water, tilted the washer on its side,removed the small gray access panel located on the back of the washer, removed both hoses and the drive belt. Then I removed the three screw bolts that hold the water pump in place. Then I replaced the old pump with the new on by just following the process in reverse. I did notice that the new pump did not come with a metal support plate(at least thats what I called it. No problem though when I found out from a local repairman that its a newer design. Total time less than 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Drain Pump

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerSONY from CONCORD NC

The washer was making a fine squeeling noise that created a foul burning odor

Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 27