| |
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerJoe from Clearfield PA
Water leak
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Pliers, Socket set
CustomerEric from Allenton MI
Washer shaking during spin cycle and load noise when during agitation
Removed front and rear panels, removed belt, removed old springs, disconnected bleach and pump lines from tub and lifted entire tub/transmission assmebly from washer. Replaced snubber ring at bottom of transmission assembly by backing off screws just enough to allow old ring to be removed and new one to be installed. Replaced pump assembly by removing drain hose and three bolts. Installed in reverse order. Placed tub/trans assembly back into washer and installed new springs using vise grip pliers. Reconnected bleach line and pump lines to tub. Reinstalled fron and rear panels. Installed new belt on bottom side of washer. Piece of cake.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers, Socket set
CustomerMichele from Lebanon PA
Started making loud screeching noise(bad bearing)
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers, Socket set, Wrench(Adjustable)
CustomerMilton from bartlett IL
Discharge pulley assembly bearing going out on it.
Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers, Socket set
CustomerPatricia from Modesto CA
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I finally decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Socket set
CustomerLon from Morton Grove IL
Water pump replacement
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerBILL from DIX IL
The pump went out & water was all over my floor..
UNSCREWED THE FRONT PANEL. tHEN TOOK PUMP OUT & PUT NEW ONE IN.....
THANK YOU PART SELECT.COM...SUPER FAST SHIPPING...
|
3 of 9 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers, Socket set
CustomerGary from Deming NM
Water pump quit working
unpluged the machine , turned off the water .
removed as much water i could by hand ,with pan & towels .
Removed the front panel , tip machine on back feet & prop up .
removed belt from under the machine , take the drain hose off pump , remove pump .
installed new pump , rehook hoses , install new belt & motor pivot spring .
put front back on lower machine turn water back o
n , and plug back in .
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers, Socket set
CustomerDaniel from Hinsdale IL
Pump was making a grinding noise.
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerTery from Orange CA
Noisy pump
Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerLes from Moneta VA
Made noise on spin cycle
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers, Socket set
CustomerLarry from Waukesha WI
Water would not drain and tub would not spin.
I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerColin from Dauphin PA
Grinding sound when unit was running and eventually locked up
Had to change the drain pump, the bearing was shot and was the reason for the noise and the eventual stopping/belt breakage....Watch the video on this site for the drain pump procedure it's very helpful....The drain pump swap-out was very easy...Two hose clamps and three small bolts and it was done in no time..I changed out the snubber ring while I was in there... I used vise-grips to grab the the springs for removal/installation and lifted whe whole drum out....Just as others on here have suggested just loosen the retainer screws holding the old snubber ring just enough to slip it out and the new one in...It's really that easy...The toughest part is dealing with the springs and one piece of advice I can offer is to start with the hardest to reach first and save the easiest for last upon reassembly...Put it all back together and installed the new belt...DONE !!! Works like a champ !!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers
CustomerRichard from Jacksonville FL
Vibration
Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyDifficult
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers, Wrench set
CustomerTheresa from Zanesville OH
Needed to replace the water pump
The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.
|