http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/PLJP1DRY.gif
See part 52 in the diagram

Single Roller

PartSelect Number PS2345839

Also known as Wheel.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $4.60
  • You Save

    $.77
  • Your Price

    $3.83
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Roller Pin

Part Number 2163774

This roller pin is used with a refrigerator's roller.

$3.96
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 5 reviews What's this?
1-5 of 5
 

6 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

Customermike from holly springs NC

Left front plastic wheel was broken

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerJohn from Capac MI

Broken roller

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Single Roller

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerRalph from Camillus NY

The plastic wheel broke in half at the right front of the refrigerator.

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:1- 2 hours

ToolsPliers, Socket set

CustomerWilliam from Lone Tree IA

Ice maker was over flowing filling the freezer with water and ice.

As per suggestion I replaced the water inlet valve.
I pulled out the refrigerator and removed the cardboard panel. I removed the water inlet unit by removing two screws. I used pliers to take off the the tubes to the ice maker and the water. Then removed the inlet supply tube. Installation was the reverse process.

However this did not fix the problem. After further research on another web site, I realized that the diagram that was furnished by PartSelect did not fit my refrigerator. What I really needed was the ice maker module. So I need to order the right one and I can't return the wrong part because I installed it. So I just left the lever in the ice maker in the up postion. the ice maker is still not working.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Single Roller

Level of DifficultyDifficult

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerRobert from Orting WA

Broken front wheel

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5