2341924-1-S-Whirlpool-W10192799-Accumulator Filter
2341924-1-S-Whirlpool-W10192799-Accumulator Filter 2341924-2-S-Whirlpool-W10192799-Accumulator Filter http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/54093.gif

Accumulator Filter

PartSelect Number PS2341924

This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Not draining.
  • Compare At

    $86.27
  • You Save

    $14.38
  • Your Price

    $71.89
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 22 reviews What's this?
1-5 of 22
 

184 of 325 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:More than 2 hours

Tools

CustomerGilles from Cypress, CA

Machine not cleaning, leaving crud on dishes. The old accumulator filter was punctured and full of crud. One broken wheel from abuse.

Take out the old parts and clean all the ones to be reused by power washing with garden hose and/or compressor blasting. Put it all back together. BE VERY CAREFUL NOT TO PUNCTURE THE ACCUMULATOR FILTER! THE TORX SCREWS ARE RIGHT NEXT TO THE FILTER SO IF YOU SLIP AND DROP THE TOOL, THE FILTER WILL BE TOAST!

THE DISHWASHER WORKS PERFECT NOW!

Help other customers find the most helpful instructions.

Were these instructions helpful?

64 of 72 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customermike from woodland hills, CA

Maytag quiet series 300 stopped cleaning

Remove the racks top and bottom. The Station D seals are at the far back on the tube that supplies water to the top and middle spray heads. Unsnap the old one and snap in the new - it only goes one way! This will repair the seal aroound the tube that supplies the middle sprayer and restore pressure to all 3 heads. Repalcing the screen accumulator is harder. you need a torx driver. remove the little thumb nut on the bottom sprayer and remove the sprayer. Then remove the tube where you just replaced the D station. (You of course could have done this earlier if you were doing both repairs) then 6 screws on the impeller housing. Now remove the 1 torx screw on the impeller and pull the impeller up and off. Remove the 3 screws on the cover and 2 screws on the accumulator. Clean all the old food scraps that are clogging up the works and reassemble in reverse order. Washer is working again!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

27 of 30 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerEric from Newton, WI

Dishes were coming out dirty with specs of debris on them

I noticed there was a filter type of material in the bottom of the dishwasher that had a small tear in it and figured that was my problem. I removed the nut from the sprayer arm at the bottom of the tub, removed the sprayer arm, removed 3 screws of the plastic cover below that. Removed six screws on the plastic cover below that. Removed one screw fron the center of the black pump spinner wheel that allowed me to lift off that cover. Then I lifted out the flowplate assembly. Placed the new part in and reversed the steps. Works like new again! All for about $30...I am not trianed in any way and have no experience in this kind of thing but am motivated trying to avoid a large service bill for a few screws. I am so happy...Thanks PartSelect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

27 of 39 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrank from Raleigh, NC

Would not spray.

Looks like Maytag knew this was a problem. My chopper sleeve (plastic) was stripped and causing the impeller to not spin. The replacement part was all metal and was very easy to replace the old one just by removing screws. The replacement looks to be very sturdy and should last a lot longer than the original. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 25 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerBrian from Keokuk, IA

The dishwasher would not drain

First of all I shut the power off to the dishwasher at the breaker box. Turn the water off to the dishwasher. Unhook the water line and then remove the screws that go around the outside trim edge of the dihwasher that secures it to the cabinets. Then you will want to look at the adjustable legs on the dishwasher. You may need to lower the legs to get the dishwasher out from underneath the counter top. While you are doing this you should also pay attention to your drain hose. My drain hose had plenty of slack so I was able to pull my dishwasher out from underneath the cabinet and then unhook it. You should have towels or a bucket in place to catch any water that is inside the drain hose. Next I laid the dishwasher over on its left side and I was able to access the pump. I then used a flat screw driver to remove the hose clamp and remov the drain hose from the pump. I then unplugged 1 wire connector and a bracket and could turn the pump counter clockwise and removed it from the dishwasher. There is a bracket that must be removed from the old pump to the new pump. Once this is accomplished You are ready to reinstall the new pump. I took a towel and wiped the area where the pump hooks into the dishwasher to make sure all debris was removed. I then used a very small amount of gasket sealer and placed it around the "O" Ring on the new pump. Next place the pump back in the whole and turn in a clock wise direction securing it back into the dishwasher. Hook up the drain hose and the wire connector. Make sure the bracket is postioned properly and you are ready to put dishwasher back under the counter.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 22