2341899-1-S-Whirlpool-W10190965-Icemaker
2341899-1-S-Whirlpool-W10190965-Icemaker 2341899-2-S-Whirlpool-W10190965-Icemaker 2341899-3-S-Whirlpool-W10190965-Icemaker http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/ZIG3BJNW.gif

Icemaker

PartSelect Number PS2341899

This is the icemaker only. You must use the wire harness, cover and bail arm from the original icemaker.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Leaking.
  • Ice maker won’t dispense ice.
  • Compare At

    $80.12
  • You Save

    $13.35
  • Your Price

    $66.77
In Stock
Order within the next 8 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 26 reviews What's this?
1-5 of 26
 

75 of 86 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJamie from Mitchell, SD

Ice maker quit working

First I removed the three screws with a nut driver and then disconnected the wire plug from the old ice maker. I plugged in the new unit and re-installed the screws and instantly the unit started to work. I did have to adjust the water level on the unit ...just turn the small plastic knob (use a slotted screw driver) on the side of the unit counterclockwise to increase the water level (do not turn more than one full turn or you could damage the unit) . It works perfect and saved me lots of money!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

41 of 45 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerLeopold from Warren, NJ

Water overflow from the tray fusing ice cubes into a glob of ice in the bin below

The old ice maker's protective finish flaked off causing some cubes to stick to the mold and consequently water overflow into the bin below causing ice cubes to fuse into large ice globes. After reading customrs' reviews, the replacement with new icemeker from PartSelect was easy. I unpluged the fridge, loosend two screws on top of ice maker and removed one screw on the bottom, removed old ice maker and inserted the new one in its place. I reused the old wireing harness for new ice maker. It started producing ice within 2 hours and it works flowlessly since. Thank you PartSelect for sending the correct part and informative repair hints on your webside.

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 26 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerDale from Elk Grove, CA

Needed to replace icemaker

After removing the old icemaker ( 3 screws) I put the new piece right back in place . Just plugged in the wiring that was already in place from the old icemaker, Hung the new ice maker on the two screws left in the wall of the freezer. Be sure and put the arm on the new icemaker prior to hanging it on the wall. tighten the screws and put the white plastic end cap over the exposed rotor end. Turn on the water to the refridgerator and in about two hours you will have ice. Be sure and turn off the water to fridge before undoing the old icemaker and unplug the fridge from elctric outlet during the whole process. Simple

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 14 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerJames from Edmond, OK

Ice maker stopped making ice

I first went on line to trouble shoot. Discovered it was the Ice Maker itself then then I entered the part number in your system to purchase the ice maker unit. When the unit arrived I simply took a socket for three bolts unplugged the electrical connection and reversed this for the installation. It was simple. I described to my secretary the process and she told her husband who in turn replaced their icemaker.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 14 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerNancy from Ann Arbor, MI

Old ice maker was leaking

Using the video at http://www.partselect.com/PS358591-Whirlpool-4317943-Replacement-Ice-Maker.htm?SourceCode=14 I was able to swap out the old ice maker and put in the new. It was easy. The trickiest part was working in the tight confines of a full freezer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 26