2341899-1-S-Whirlpool-W10190965-Icemaker
2341899-1-S-Whirlpool-W10190965-Icemaker 2341899-2-S-Whirlpool-W10190965-Icemaker 2341899-3-S-Whirlpool-W10190965-Icemaker

Icemaker

PartSelect Number PS2341899

This is the icemaker only. You must use the wire harness, cover and bail arm from the original icemaker.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker will not make ice.
  • Leaking water.
  • Ice maker won’t dispense ice.
  • Compare At

    $78.82
  • You Save

    $13.14
  • Your Price

    $65.68
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 26 reviews What's this?
16-26 of 26
 

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRobert from Lake Forest CA

Ice maker quit making ice, timing dial had broke

After checking out the part number from the manuel that came with the fridge, I found out that the manual was wrong. After taking the old icemaker out I found it had a different part number on it. Looked it up at PartSelect and found out that the number on the old icemaker had changed. That was no problem and it was much cheaper than the one in the manuel. Anyway, I ordered the icemaker and believe it or not, I had it on my front porch the next day. It just had three screws to install and reattached the harness and it was done. Just to let everyone know it takes almost a good day before the ice started to come out, but then it started making ice as fast as before. Easy install and the price was great and service was very, very fast.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerJim from Manitowoc WI

Water was leaking from bottom of ice tray

After watching the instr. film I found it very easy to do.
This is what motivated me to do the job and save a LOT of money. It was actually the second repair I did.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set, Wrench set

CustomerRich from Arnold CA

Washer top adgitator / frig. Ice maker not producing

Washer; I watched the repair video, and replaced the agitator. It was so simple I think that it took longer to watch the video. Refrigerator; I replaced the ice maker, and the solenoid valve. It was very easy to replace the parts, however it took a while to diagnose the problem. I found an appliance repair man that told me what contact points on the front of the ice maker would trigger the clock (so I didn't have to wait for an hour for the clock to activate). There is also a set of contacts that when jumpered will trigger the solenoid valve. It only took a total of 25 minutes to fix both the washer, and the dryer. If you take a piece of 14 Ga. solid wire about 6" long and strip the ends about 3/8" and bend it into a U you have a jumper. If you jump the contact points on the front of the icemaker letters T & H this will start the clock operation. If you jump letters L & V, the solenoid should open to allow water to flow to the tray. If water does not flow, the filter should be checked in the valve. If the valve sounds like it is opening, sometimes the inlet to the ice maker can freeze stoping the flow. In my case I found the solenoid valve was getting only a week signal, and would only function about 25% of the time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Martinsburg WV

Wouldn't make ice

Just had shoulder surgery so had to use one arm. Was simple and easy. Just took out ice tray, loosed two fasteners at top, removed screw from bottom, pulled out partialy and disconected electric and removed old icemaker. Hooked up new electric and hung on two top fasteners, reinstalled bottom screw, tightened top fasteners and put ice tray back in. Was making ice within a couple of hours.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

Customerlisa from warsaw IL

No ice

followed the video instructions on the PartSelect website. No problem. Ice in about 2 hours! tnx

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRonald from Monticello IN

Icemaker stopped working

I replaced the old with the new one in about three minutes. And it started working right away. I priced a relacement icemaker in a appliance part store and it cost $50.00 more than partselect

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerNelson from Pasadena TX

Ice maker overflowing and forming ice blocks in cube tray

The teflon coating on the ice maker had worn off in a section. This was causing the cubes to stick and the tray heater to have to run longer. Which meant that water would accumulate in the tray over several cycles, eventually spilling over on a fill. The hardest part about replacing the ice maker was getting the plug disconnected. I had to use a small screw driver to push the tab that latches it down while pulling the plug out. You only have to completly remove the lower mounting screw. The top two just need to be loosened enough to remove the ice maker.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerShawn from Palm Springs FL

Was not making ice

I removed the old ice maker by unscrewing the three screws and unpluging the plug from in the back of the freezer. Then I just pluded the new ice maker in and screwed the ice maker back into place. and with in a hour it was making ice. The repair was so easy. My wife called around to the appliance repair store and the same part would of cost us twice as much. Delivery of the part was here the next day. What a wonderful company.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerTheodore from Kennesaw GA

Icemaked did not make ice, would not turn all the way to kick out the ice

Unplugged the fridge. Took the old icemaker out by loosening 2 screws on top of it with a nut driver, and removed one phillips screw from the bottom, then lifting the ice maker off the upper screws. Unplugged the ice maker from the plug at the back wall. Took the cover of the front of the ice maker and looked up the replacement part number. Ordered the part Monday, and it arrived in Thursday. It was exactly the same. Connected up the electrical connector, hung the ice maker on the top two screws, installed the bottom screw, and tightened the top two screws with the nut driver. It was making ice in a couple of hours.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDallas from Meridian ID

Gear in ice maker had broken

Pretty easy to replace, once you find the screws. One of them you can see on the bottom. The other two you have to feel for. Completely remove the screw on the bottom, that you can see and then loosen the two you have to feel for. Once everything is loosened, left the icemaker up and it will come free. Move it out and unplug the power cord. Make sure the power is off before you start this project. Use a small flat screwdriver to hold down the tab so the power cord will detach. Reverse the steps to install the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 8 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsSocket set

Customermichael from Mcalle TX

The icemaker stopped making ice

when I found out that the icemaker was not functioning,I took it off and check the part in partselect.com.I placed my order after 3 days the part came and I immediately installed it in less than 15min & overnight in the morning the ice receptacle is full of ice ,thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-26 of 26