2341899-1-M-Whirlpool-W10190965-Icemaker.jpg
2341899-1-S-Whirlpool-W10190965-Icemaker.jpg 2341899-2-S-Whirlpool-W10190965-Icemaker.jpg 2341899-3-S-Whirlpool-W10190965-Icemaker.jpg

Icemaker

PartSelect Number PS2341899

This is the icemaker only. You must use the wire harness, cover and bail arm from the original icemaker.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker will not make ice.
  • Leaking water.
  • Ice maker won’t dispense ice.
  • Compare At

    $85.09
  • You Save

    $14.18
  • Your Price

    $70.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 26 reviews What's this?
1-15 of 26
 

37 of 43 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJamie from Mitchell SD

Ice maker quit working

First I removed the three screws with a nut driver and then disconnected the wire plug from the old ice maker. I plugged in the new unit and re-installed the screws and instantly the unit started to work. I did have to adjust the water level on the unit ...just turn the small plastic knob (use a slotted screw driver) on the side of the unit counterclockwise to increase the water level (do not turn more than one full turn or you could damage the unit) . It works perfect and saved me lots of money!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

31 of 34 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerLeopold from Warren NJ

Water overflow from the tray fusing ice cubes into a glob of ice in the bin below

The old ice maker's protective finish flaked off causing some cubes to stick to the mold and consequently water overflow into the bin below causing ice cubes to fuse into large ice globes. After reading customrs' reviews, the replacement with new icemeker from PartSelect was easy. I unpluged the fridge, loosend two screws on top of ice maker and removed one screw on the bottom, removed old ice maker and inserted the new one in its place. I reused the old wireing harness for new ice maker. It started producing ice within 2 hours and it works flowlessly since. Thank you PartSelect for sending the correct part and informative repair hints on your webside.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsSocket set

CustomerJames from Edmond OK

Ice maker stopped making ice

I first went on line to trouble shoot. Discovered it was the Ice Maker itself then then I entered the part number in your system to purchase the ice maker unit. When the unit arrived I simply took a socket for three bolts unplugged the electrical connection and reversed this for the installation. It was simple. I described to my secretary the process and she told her husband who in turn replaced their icemaker.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerDale from Elk Grove CA

Needed to replace icemaker

After removing the old icemaker ( 3 screws) I put the new piece right back in place . Just plugged in the wiring that was already in place from the old icemaker, Hung the new ice maker on the two screws left in the wall of the freezer. Be sure and put the arm on the new icemaker prior to hanging it on the wall. tighten the screws and put the white plastic end cap over the exposed rotor end. Turn on the water to the refridgerator and in about two hours you will have ice. Be sure and turn off the water to fridge before undoing the old icemaker and unplug the fridge from elctric outlet during the whole process. Simple

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRichard from Charlotte NC

Would not make ice

removed 3 screws and power wire clip, removed old ice maker, reinstalled new ice make by snaping in power wire clip and the 3 screws that hold ice maker, reinstalled wire bracket/arm that stops ice maker once tray is full of ice. done

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerNancy from Ann Arbor MI

Old ice maker was leaking

Using the video at http://www.partselect.com/PS358591-Whirlpool-4317943-Replacement-Ice-Maker.htm?SourceCode=14 I was able to swap out the old ice maker and put in the new. It was easy. The trickiest part was working in the tight confines of a full freezer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerLarry from Merritt Island FL

Telfon coating peeling from ice maker mold

Removed and replaced the ice maker

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBrian from Alto MI

Ice maker stopped producing

Used a voltage meter to detect the problem (used a video from the web to determine how to isolate the problem. I needed to replace the unit, that I had repaired two years ago for $150.00 or more for parts an a service call. The part I ordered came right away and the repair took about 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRobert from Kansas City MO

Icemaker not working

removed 3 screws with 1/4 nutdriver and unplug icemaker and removed from Refrigerator. Waited for 2 days and new icemaker arrived. Plug in icemakes mounted using the 3 screws. Done in less then 5 min. working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerthomas from galena IL

Ice maker quit working

I ordered a new ice maker and replaced it. It hung on two screws in the side of freezer and connected to the electric in back by a plug in unit. Within 20 minutes we were making ice again. Awesome!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRobert from Lake Forest CA

Ice maker quit making ice, timing dial had broke

After checking out the part number from the manuel that came with the fridge, I found out that the manual was wrong. After taking the old icemaker out I found it had a different part number on it. Looked it up at PartSelect and found out that the number on the old icemaker had changed. That was no problem and it was much cheaper than the one in the manuel. Anyway, I ordered the icemaker and believe it or not, I had it on my front porch the next day. It just had three screws to install and reattached the harness and it was done. Just to let everyone know it takes almost a good day before the ice started to come out, but then it started making ice as fast as before. Easy install and the price was great and service was very, very fast.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJoao from Chandler AZ

Part was demage , old

removed old part and instal the new one :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJames from Wadsworth OH

Wasn't making ice

There are 3 screws the one on the bottom comes all the way out, the 2 on top just need to be loosened. Lift up on the ice maker to clear screws, pull away a little bit then while holding disconnect the wire harness from the ice maker by pushing down the locking tab with a flat head screw driver. Then reversed the process with the new one, it took an hour or so but the ice started falling, a day later the bucket was full.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerAlain from Lutherville MD

Ice maker stuck and not making ice cube

1- remove the ice make assembly to check out the ice maker: remove 3 screws with a nut driver, and aplug the electrical connector
2- checked that the ice maker assembly was not fixable (visual inspection)
3- Ordered an ice maker for PartSelect,
4- got it 2 days later, reconnected the electrical connector and put the 3 screws back

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Icemaker

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Martinsburg WV

Wouldn't make ice

Just had shoulder surgery so had to use one arm. Was simple and easy. Just took out ice tray, loosed two fasteners at top, removed screw from bottom, pulled out partialy and disconected electric and removed old icemaker. Hooked up new electric and hung on two top fasteners, reinstalled bottom screw, tightened top fasteners and put ice tray back in. Was making ice within a couple of hours.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 26