BBB A-Plus
2341896-1-M-Whirlpool-W10190935-Icemaker-Control-and-Motor-Assembly.jpg
2341896-1-S-Whirlpool-W10190935-Icemaker-Control-and-Motor-Assembly.jpg 2341896-2-S-Whirlpool-W10190935-Icemaker-Control-and-Motor-Assembly.jpg 2341896-3-S-Whirlpool-W10190935-Icemaker-Control-and-Motor-Assembly.jpg

Icemaker Control and Motor Assembly

PartSelect Number PS2341896

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker will not make ice
  • Ice maker won’t dispense ice
  • Leaking water
In Stock

  • Compare At

    $117.49

  • You Save

    $19.58

  • Your Price

    $97.91
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos

For installing this part.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 3 4 5 6 ... 13 NEXT > 31-45 of 193

 

2 of 3 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMarinus from Crestone CO

Ice maker stopped working

Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking care that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerkandra from newhall CA

Wasnt making ice

followed instructions provided when ordering part

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerPaul from Boring OR

Motor assembly was shorting out

I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.

Paul First time dealing with you ,thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly
    • Ice Mold

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerMatthew from Collegeville PA

Coating (clear) on ice cube mold peeling off

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for several hours/days. You will have to defrost to begin making ice again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMichelle from Redwood City CA

Ice maker stop making ice

Open the icemaker service, door slide it out, remove wiring, remove ice maker control cover,remove 3screw, put new one in, put everything back together and with in 6 hours we have ice again. PS my husband did it though.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerKeith from Green Valley AZ

Ice maker would not turn off. Kept making ice! Even turned off all water to house, but then realized that ice maker was being fed by pressurized ro tank!!

Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerWayne from Castile NY

Would not complete ice-making cycle.

Unplugged the refrigerator. No need to remove the entire icemaker (IM). Removed the old module by taking out the 3 screws and carefully wiggling it free from the icemaker. Lined up the blade arm with the new module, pushed the module onto the IM and put in the 3 screws. Lowered the shut off arm and plugged in the refrigerator. Once the freezer compartment reached the proper temperature, the IM began making ice with no further problems.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRick from Rockford MN

No ice!

After reading the stories on your site, I figured it had to be the motor control. Easy to take off, but had to take the tray off the freezer wall to get the ice out. Once I did that it was a piece of cake. Now I have ice (and vodka tonics...).

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEugene from Sun City West AZ

Ice maker not producing ice

I found your website while searching the internet for a repairman. My fridge was making strange clicking sounds and no ice. I suspected a certain part after reading the testimonials on your website. The part I ordered was delivered in less than a week and I installed it in less than 5 minutes. I probably saved about $200.00. Thank you!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyEasy

Time to do repair:30 - 60 mins

Tools

CustomerMarv from Fort Smith AR

Teeth on the wheel were broken off.

I don't know how he did the repair, but he told me it was simple, and I know it saved us a lot of money! Thank you for your excellent help and the delivery was like overnight!!
Submitted by
"The Wife"

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBen from Grovetown GA

Would not make ice...plastic gear broken on module

after reading reviews on changing the control module I decided it couldn't be very difficult. I was rewarded because it wasn't. It took less than 20 minutes to change the module. At first I was concerned because the wheel did not start turning as soon as power was connected. I discovered this is normal and 30 minutes later the icemaker was making ice again. Simply remove the 3 screws, carefuly pull the module away from the shutoff arm, and pull it out. putting the new one in is the exact reverse. You just have to realign the ejecter cam in the icemaker with the new module so it slides right in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJames from Van Buren AR

Ice maker not making ice

When I took the ice maker apart I noticed that the shaft of the motor control wheel was broken so when it turned it could not trip the control contacts nor rotate the ice ejector fingers. I ordered a new control and motor assembly which arrived two days later. It was very easy to install and now the ice maker works perfectly.

PartSelect was a great help. A local appliance parts warehouse stocked parts for my ice maker but they only stocked a kit that contained other parts that I did not need. Ordering from PartSelect saved me over $35.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRon from Fulton MO

No ice

Did not have to remove the complete ice maker. Only the front part that housed to motor assembly. Two Clips removes to cover and three screws removed the motor unit and the rest was in reverse. No wires to disconnect or connect. It just plugs in to unit. Works great and cheaper than from Sears Parts Direct shipping cheaper also. Will buy from Part Select again.
Thanks, Ron

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerSean from Lancster CA

Ice maker stopped making ice

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Icemaker Control and Motor Assembly

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRichard from Lewistown PA

Icemaker shaft would not turn

Installed new motor control

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 3 4 5 6 ... 13 NEXT > 31-45 of 193