Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2341896
This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I ordered the part and just 1 1/2 days later, it arrived! Awesome!I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.
Help other customers find the most helpful instructions.
Were these instructions helpful?
It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work. Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly. Thats what took 15 minutes but after me and my wife worked on it, we had a bucket of ice by morning!We only knew how to do what we did because of reading these messages on this site. It came with no directions.
I unpacked the motor and looked at how it was supposed to go in. I removed on screw in the right rear of the ice maker. Pushed a tab on the left of the ice maker. Removed the entire assembly and unhooked the electrical part of the ice make. unscrewed the three screws holding the motor in place and replaced the motor. Put everything in back together and in 15 minutes the familar sound of the ice maker could be heard.
Removed icemaker by first removing the nutscrew that holds the cover to the electrical connection in place. Next, I removed the door then slid the icemaker out and diconnected the electrical connector. With the icemaker out, I R&R'ed the motor assy , reconnected the electrical, and slid the icemaker back in place. Next, I replaced the door, turned the icemaker switch on and waited. In about 30 minutes I heard the water being injected into the icemaker, and soon there was ice. The repair was easy and inexpensive. Tx to Partselect which I found on Google.
unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix
Went very easy, watched the video from the web site and did what it showed to do and put it together and it worked.We now have ice.
I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.The module cover is removed, then the module itself is easily removed by removing three screws.The assembly is just as easy. A few hours later, I had a half bucket of ice!
Very, very easy. Went to PartSelect and watched the repair video. Took the ice maker out, removed the end cover and found that there was a burned circuit on the board. Went back to PartSelect and ordered the part on a Thursday afternoon. Received the part Friday morning! 15 minutes to replace the part and now we have ice again. This is my second order through PartSelect and both times the cause was easy to determine, instructions were clear, and delivery of the parts were quick. Very good web site.
Just like the instructional video showed. 10 minutes, a nut driver and a screw driver, and we were back making ice.
It was very easy, I took ice maker apart and immediately figured the motor had burned out you could smell it. I looked at parts and easily found the exact part part I needed. It was sent to me in just a couple of days and I put it back together in minutes and it was making ice again in no time. I'm sure I saved myself slot by doing it myself.
read a lot of how-to's and forums, but it was the video's posted by partselect on YouTube that intrigued me to try my own hand at trying to find the correct part for the fix. this is why i ordered from partselect rather than search elsewhere. I ordered on Wednesday night and had the ice-maker making ice on Friday night. I used the electric tape to hold the flapper and light switch off to simulate the door being closed.
followed instructions from Partselect on- line video.
My husband had taken the ice maker out and deceide which part we would need to fix the maker. your online parts list made this possible. The service you provide was most helpful. The shippment got it to us in record time.
easy as pie everthing good thanks
After reading solutions to my problem on your website I ordered the part which fixes 50% of the problems. When I got back after Christmas the part had arrived. I removed the Icemaker and replaced the part. It took aprox. 20 minutes for the job. It was easy. Now we have ice cubes again.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.