Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2341896
The icemaker control assembly is located in the freezer section of your refrigerator. It is what controls the icemaker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions, such as the heater, the water inlet valve, the cube size, and cube ejection. This replacement includes the control module and the motor, the motor is not sold separately. There are a number of reasons you might need to replace this part: if the motor is faulty, if any of the gears are worn out, or any of the plastic pieces are broken or damaged. If your icemaker is not functioning properly, you should start by testing this module. Before you begin repairing your refrigerator, make sure it is unplugged.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I received the part in half the expected time. Installed in 15-20 minutes, and an hour later it was making ice again. Yeah, no more bagged ice from the store!!!
Help other customers find the most helpful instructions.
Were these instructions helpful?
I pulled the ice maker apart, did an Internet search for the parts and found this site. From the other posts, it sounded like all I needed was to replace this part and that proved to be true. Simple, quick, and easy. And these guys shipped it fast. Zero complaints all around.
1. Turned off water supply. 2. Up pluggeg refrigerator. 3. Opened freezer door to access ice make. 4. Remove plastic panel door by ice maker, 5. Remove one hex screw with nut driver. 6.Remove plastic cover over water fill spout. 7. Pull ice maker forward to access power cables. 7. Unplug power cable. 8. Remove 3 phillips srews holding timing assemble to icemalker. Reverse procedure to install. Very easy, so far the icemake is working great.
First I looked on your site to find why it was not making ice. Then i found out what part was bad. I got my model number ordered the part. Three days part was at my door.You gave me instruction on how to slide out ice maker disconnect plug,remove end cap from ice maker unscrew assembly with philip screwdriver remove old part install new part in reverse order. Reassemble icemaker in reverse order slide back in place turn on power. Should be producing ice in a couple of hours very simple.
I read the many articles on PartSelect's website and went with the numbers on probability. Numbers don't lie it was the Icemaker Control Module a simple three screw disassembly, pop the new one in, and put the rest of it back together. It literally took 20 minutes! Thanks Partselect I am enjoying my nightly icey drinks thanks to your website and I saved about 150 bucks in the process.
I checked water valve, OK. No ice plug in supply tube.Power to ice maker OK. Conclusion defect control.Placed order for part and amazingly received it the next day.Unscrewed old part installed new part and it started makingice in about 3 hrs. Time to install 15 minutes.marinus Cape Coral.
Replaced the ice maker motor did not fix ice maker. Next thing to replace is the control unit but i don't know for sure that is the problem.
Unplug fridge. Remove ice door. Removed one 1/4" screw from right rear. Remove wire harness cover. Release catch on left side and slide ice maker out. Pop cover off left side. Three screws hold in control module. Line up ejector arm cam with new module and reverse the removal process.
I'm a pretty handy guy. I can usually figure out how to fix most things. We have an extended warranty for most of our appliances but the refrigerator was somehow over looked. After reviewing the info package that come with the refrigerator I realized I was pretty much on my own. I went on the Internet and was lucky to find the Partselect site. It was great and easy to navigate!!! I love the virtual repairman and the section that gives percents of probability of what the problem may be. I ordered the part, received it the next day and had it repaired in minutes. Just watch the virtual repairman and do what he says..it couldn't have been simpler The whole process (ordering to shipping to installation) was extremely easy. If I ever need parts for any appliance again I will go to Partselect!!!!!!!!!
I want everyone to know that the ice maker for my sub zero was no longer available.It is a 1994 refrigator. I searched your web site and found something that looked very similiar.It turned out to be an exact replacement.If anyone needs the entire ice maker, they will have to change the electrical connection on the unit.To remove the ice maker unit,first remove the feeezer draw. It comes out the same way you would remove a kitchen draw from the cabinet.Unplug the ice maker,and remove the 3 screws.Then remove the 3 screws from the front of the ice maker.Reverse the process to re-install.
I watched the video of how to do it. I removed old one and I installed new one as per video. It took less than 15 mins. EASY !!!!!!!
Remove ice maker from side wall of freezer. Not alot of room to see the fasteners because the unit is a side by side. Overall pretty easy fix and saved alot of money instead of calling in repair man.
Refrigerator is 4 year old. Icemaker quite working after about a year. Called a repair man that fixed it for about $300. Unfortunately, it quit working again after a year. Found the PartSelect website and read the other repair stories so I decided to take a shot at doing it myself. Man am I glad I did.The repair stories were very helpful. I thought the problem would either be the motor or the optical sensor so I purchased both. I decided to replace the optical sensor first since the LED light was flashing. I unplugged the refrigerator and removed the three screws holding the plastic cover plates on the left and right side of the freezer. Unplugged the wire harnesses and plugged into the new boards. Replaced the screws and in a couple minutes I heard the icemaker fill with water. 30 minutes later we had ice. Using PartSelect saved me $200. I will definitely use PartSelect in the future.
First I removed the cover over the motor assembliy,then took out the three phillips screws holding the assembily, then unpluged it. then I pluged the new unit in holding the shut off bar( for when the ice tray is full) in place. then put the three screws back in, pluged the fridge in and the ice maker started working. I put the cover back on and the job was complete. this was a very easy fix.
The first step is to turn the icemaker switch (located inside the freezer) off. Then, I removed a single nut to the right rear of the icemaker unit and loosened the clips that hold the unit in position (one clip on each side). Next, I disconnected the wires (you have to hold the clip open to pull them apart).Once the unit was out, I removed the old motor module by removing the three screws that hold it in place. I installed the new motor module, and then reconnected the wires and put the unit back in the freezer. One nut to hold the unit in place, and turn the icemaker switch back on.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.