2341877-1-S-Whirlpool-W10189966-Electronic Machine and Motor Control Board
2341877-1-S-Whirlpool-W10189966-Electronic Machine and Motor Control Board 2341877-2-S-Whirlpool-W10189966-Electronic Machine and Motor Control Board

Electronic Machine and Motor Control Board

PartSelect Number PS2341877

This part is also used as a water pressure transducer.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Timer will not advance.
  • Compare At

    $417.54
  • You Save

    $69.59
  • Your Price

    $347.95
In Stock
Order within the next 12 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 4 reviews What's this?
1-4 of 4
 

111 of 127 people found this instruction helpful

Parts Used

  • Electronic Machine and Motor Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJames from Turnersville NJ

Washer always stopped at the 47th and 24th minute of each load and display f1 error code. I would have to press "cancel" and then "start" a few times for it to continue.

Removed the dial control top covering by unscrewing the 3 screws in the back of the cover. Once the cover was off, the control module was exposed and all I had to do was:

1. Disconnect the wires that were plugged into the control module

2. Remove the old module. There was 1 screw holding it in place.

3. Replace with the new module. Put back the screw back.

4. Reconnect the wires. There was about a 8 different plugs that needed to reconnected. So I took a few pictures of how the wires were connected/plugged in, with my compact camera (just in case I forgot where each went). I didn't need to use the pictures, but it was just a safety net in case I forgot where each went.

Help other customers find the most helpful instructions.

Were these instructions helpful?

36 of 40 people found this instruction helpful

Parts Used

  • Electronic Machine and Motor Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerArthur from Linden NJ

Within 10 minutes of starting the washer, it would stop. Grreen flashing lights and f1 error code appeared.

Someone on Google suggested holding the stop button and the start button at the same time for 60 seconds as a way of by passing the problem. This did work but soon became a pain each time we used the washer.Installing the new part was super easy. Three screws hold the cover on, one screw holds the part in place and all the plug- ins are marked by color as to where they go. Pretty hard to mess it up.I did take a few digital pictures before just in case.

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 29 people found this instruction helpful

Parts Used

  • Electronic Machine and Motor Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRichard from Cartersville GA

Control panel

Google seach and search on Parts Select. Easy repair

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 24 people found this instruction helpful

Parts Used

  • Electronic Machine and Motor Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

Tools

CustomerJenny from Stone Mountain GA

Replaced main control due to f1 error code.

Followed the directions given in other client reviews. It was easy and works perfectly now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4