http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/55659.gif
See part 11 in the diagram

Silverware Basket - Gray

PartSelect Number PS2341016

This part has been redesigned by the manufacturer and is now a complete full basket with handle and covers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning properly.
  • Leaking water.
  • Door latch failed.
  • Unusual Noise.
  • Compare At

    $16.09
  • You Save

    $2.68
  • Your Price

    $13.41
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 101 reviews What's this?
1-15 of 101
 

464 of 468 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerCheryl from South Burlington VT

Bottom rack needed replacing

Just took it out of the box and slid it in.
Only problem I encountered, and I think it was due to the age of the dishwasher, was the newunit was not as deep as teh original rack. This will require a new method of loading dishes. Also, the new basket doesn't really fit well in the new rack.
Still cheaper than replacing a good cleaning dishwasher!

Help other customers find the most helpful instructions.

Were these instructions helpful?

375 of 379 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJanet from Plano TX

The utensil basket was old, bowed and the bottom was falling out.

I ordered a new replacement basket. The new one is a little different but it fits in the same place and takes up the same amount of room in the dishwasher. It looks very nice too.

Help other customers find the most helpful instructions.

Were these instructions helpful?

208 of 409 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set

CustomerCHRISTOPHER from Spalding NE

Wash quality was getting bad

THE UPPER ARM WAS HELD IN BY A TORX SCREW. THE SHOULDER ON THE SCREW HELD THE ARM IN PLACE. ONCE REMOVED I SIMPLY SWAPPED PARTS AND INSTALLED SCREW. THE LOWER ARM WAS HELD ON BY A PLASTIC NUT WITH KNURLED EDGES THAT YOU CAN REMOVE BY HAND. THE ARM SIMPLY LIFTED OFF AND I SWAPPED ARMS AGAIN. THE ROLLERS ARE HELD ON BY A CURLED PLASTIC LOCK THAT GRIPS THE WIRE BASKET.

Help other customers find the most helpful instructions.

Were these instructions helpful?

133 of 200 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerKenneth from Houston TX

Maytag makes a really crappy silverware basket. The bottom of ours fell apart the first year.

There was no repair to be done. Just replaced the defective basket with the new one.
I got the part two days after ordering it. Great service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

93 of 94 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerWade from Seattle WA

The bottom of our dishwasher's old utinsel basket broke out

It was so easy to find the right part on the PartsSelect website. I just had to enter the manufacturer (Maytag) and model number and up popped skematics of all the parts available. I just clicked on the drawing of the basket and placed the order. It took less that 5 minutes. The part arrived 4 days later as promised. The repair took even less time than teh ordering. I simply took the old basket out and dropped in the new one.

I'm just happy to know there is a place that has such a user friendly website and stocks so many parts for older appliances. I had my house built in 1992 and several of the appliance are original. Fortunately I always keep the owners manuals for every piece of equipment so the model and serial numbers are readily available.

Help other customers find the most helpful instructions.

Were these instructions helpful?

127 of 250 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerLiz from Alexandria VA

Dishwasher lower basket suffered from wear and tear

Slipped into place the two wheels on lower basket that had gone missing; removed brackets for adjustable section that were broken and easily snapped knew ones into place; connected handle to flatware basket and replaced the old one. Why we didn't do this years ago!

Help other customers find the most helpful instructions.

Were these instructions helpful?

95 of 158 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerDayna from Logan UT

Worn out silverware basket

Ordered replacement basket online at much better price than available localy. When I recieved it discovered that it did not include the handle, but was suprised to see it labeled as "Genuine Maytag Parts" ( I realy expected a knock-off replacement part for the price difference). I was able to remove tha handle from the old basket and install it on the new one. Job done. No problem

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 17 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerWayne from Moreno Valley CA

Water leaking out of bottom of door when running

Replacing bottom spray arm to fix leaky door:

To fix the leak in the door it is necessary to replace the bottom spray arm. This is because when the lower spary arm fails it gets small splits which, when spraying, send water up into the door vent and inside the door. It then leaks out the bottom of the door to drain.

1. Take out he bottom dish rack.

2. Locate plastic nut (lower spray arm cap) on lower spray arm (see parts diagram).

3. Remove plastic nut (lower spray arm cap) by hand - it twists counter clockwise to loosen.

4. There will be a small piece (jump-up nozzle) under the plastic nut (lower spary arm cap). Note how it was situated. Place it aside with the lower spary arm cap - you'll need them both during reassembly.

5. Pull off lower spary arm and filter guard (they are attached to each other).

6. Note how the lower spray arm was attached to the filter guard. The top and bottom of the lower spray arm are not the same.

7. Unsnap lower spray arm from filter guard by pulling up on one side and then the other to removed it from the plastic clips on the filter guard.

8. Install the new lower spray arm, by snaping it into the plastic retainers on the filter guard, one side at a time. Make sure you installed it with the correct side up.

9. Remove the two metal pieces (Radient Shield)from each end of the old lower spray arm and place the on the new lower spray arm. A small flat head screwdriver is useful to assist in removing them from the old arm.

9. Place the assembly (lower spray arm and filter guard) back onto the dishwasher and place the jump-up nozzle back into position.

8. Attach the palstic nut (lower spray arm cap) and tighten clockwise until secure. Don't over tighten.

9. Slide the bottom dish rack back into position.

This will fix the problem of the leaky door. I went ahead and replaced the upeer spray arm at the same time since it was a connvient time to do so.
If you wish to do so read on.

Replacing upper spray arm.

1. Remove the bottom dish rack.

2. You can remove the top dish rack, but you don't need to.

3. Examine where the upper spray arm is attached to the dishwasher. You will see three parts. The one on the spary arm center - toward the inside of the dishwasher is the SNAP SPRAY RETAINER. Next is the UPPER SPRAY ARM itself. Next, between the UPPERT SPRAY ARM and the body of the dishwasher is the SNAP OUTLET NUT.

4. Remove the SNAP OUTLET NUT by turing it counter clockwise (remember its upside down so you have to be looking up at it to determine which way is counter clockwise). I had to use a screwdriver blade and the palm of my hand to get it to loosen - I set the blade against one of the Knurls on the nut and gave it a tap with the palm of my hand).

5. The whole assembly will drop down. Remove it from the dishwasher. Note the way the UPPER SPRAY ARM is positioned; as the two sides are different.

6. With a pair of needle nose pliers compress the wings of the SNAP SPRAY RETAINER and remove it from the assembly. The assembly is now in three pieces.

7. Replace the old UPPER SPRAY ARM with the new one - again make sure it is in correctrly, as there is a top and bottom to the spary arm.

8. Insert the the SNAP SPRAY RETAINER into the new UPPER SPRAY ARM and into the SNAP OUTLET NUT. Place the assembly back into the dishwasher by tightening down the SNAP OUTLET NUT - turning it clockwise to tighten.

9. Replace the uppper dish rack if you removed it.

10. Repalce the lower dish rack.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 17 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerKEVIN from Woodbury MN

Latch broke completely and then shortly thereafter due to the extra pressure put on the control panel handle lip the top part of the panal broke off.

removed all screws that held the door liner in place @ 10 then removed the 6 screws that held the control panel in place. control pane came off easily. as the latch was broken that came off easy too. The replacement panel and latch fit perfectly. the only trouble I had was inserting the flat wiring bundle from the new control panel to the old circuit board connector. Take your time and really seat the flat wire bundle into the circuit board. it needs to be nice and snug. if it's not only a few of the wash functions will light up when pressed. once the connection is tight all functions worked. replace all screws - easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 12 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLinda from Owasso OK

Silverware basket broken - replaced with new one

I was able to remove the old handle and place it on the new basket - using only a screw driver.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 13 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerMarge from Cranford NJ

The basket in our dishwasher had many broken parts on the bottom and the silverware kept falling through

We were happy to find the basket we needed listed on your website, even after we could not find it on the Maytag site. It was perfect. I can't believe we lasted almost 2 years with the broken basket we had.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerEric from Ellensburg WA

Door latch and seal not working correctly and broken

Removed the screws holding the door liner in place removed latch. Waited for half of the parts to get here, about 2 weeks. Parts got here except for Door latch and seal they were back ordered. One month after I ordered all parts finally arrive. Replace door latch assembly and replace door seal reinstall retaining screws....Done works good again. Parts were all the correct ones just took a long time to get here.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Silverware Basket - Gray

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerD from Villas NJ

Original basket fell apart

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerJohn from Winsted CT

Broken basket

Two day service...can't get better than that!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSuzanne from Jackson TN

Silverware basket had broken through on the bottom and silverware would not stay in. Handle was tricky to put on. Bottom rack one of the adjustable racks had broken.

Basically took out of box and put in dishwasher.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-15 of 101