2340910-1-S-Whirlpool-6-917075-Discharge Pump Housing
2340910-1-S-Whirlpool-6-917075-Discharge Pump Housing 2340910-2-S-Whirlpool-6-917075-Discharge Pump Housing http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/53879.gif

Discharge Pump Housing

PartSelect Number PS2340910

This part is located under lower spray arm.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Not cleaning dishes properly.
  • Not draining.
  • Compare At

    $100.84
  • You Save

    $16.81
  • Your Price

    $84.03
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 41 reviews What's this?
 

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerEric from Gualala, CA

Grinding noise/dishes not washing properly. Soap not dissolving

Other parts used:
Lower Spray Arm (#2)
Upper Spray Arm (#33)
Snap Spray Retainer (#31)

Removed upper and lower washing baskets.

Pulled off Upper Spray Arm (#33). It pulls off easily by hand. No tools required. Replaced with new Upper Spray Arm (#33) and Snap Spray Retainer (#31).

Removed Large Spray Arm Cap(#34,)which has a right hand thread. This allowed me to take the Lower Spray Arm(#2)off.
Removed Filter Guard (#36).

Next I removed the 6 screws from the Pump Cover & Secondary Filter Assembly (#4) with a Torx screwdriver. Removed Lower Spray Arm Seal(#3), Pump House Filter (#6)(which I cleaned), Assembly, Rinse Arm (#7) Jump Up Nozzle (#1). Unscrewed Discharge Housing Nut(#8) by hand. Removed Support, Wash Arm (#9). This allowed me to remove the three screws holding the Discharge Housing Assembly(#11)with a 5/16th nut driver. Next I removed the Impeller Screw (#12) with a 5/16th nut driver. You must hold the Impeller Assembly (#14) firmly while loosening the nut. Removed Impeller Assembly (#12) and Plate, Suction (#15). Cleaned out area of debris,lint, etc. Put back old Plate, Suction (#15) and replaced Impeller Assembly (#14) with new part. Replaced Upper Housing Gasket and Discharge Housing Assembly with new parts. Put back all parts in the reverse order I removed them replacing the O-Ring (#37) with a new part. This O-Ring goes in the Pump Cover & Secondary Filter Assembly (#4).

After completely assembled it ran as good as new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerWANDA from CLINTON, MI

Replaced broken and worn parts

removed necassary parts

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

Customergregory from Staten Island, NY

Ratteling noise

unscrew screen and cover and unbolt impeller replace with new parts. everything goes back together easily, anyone with even minimal repair skills should be able to do this repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerROBERT from NORTH ATTLEBORO, MA

Water would enter the machine but no wash cycle

removed the agitator,and a couple of baskets til i was able to gain access to the pump impeller & pump housing. i replace those parts,put back together,all works great now

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 12 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerJohnny from Paducah, KY

Discharge housing backing plate broke off

From the inside I removed all of the accesories down to the impeller . I replaced the impeller as a precaution measure just incase any wear from the backing plate of the dischareg housing coming undone. and reassembled the unit. It is very easy if you have a repair manuel. I received my parts the next day. Great company

Help other customers find the most helpful instructions.

Were these instructions helpful?