2338652-1-S-Whirlpool-W10170080-Front Bearing
2338652-1-S-Whirlpool-W10170080-Front Bearing 2338652-2-S-Whirlpool-W10170080-Front Bearing 2338652-3-S-Whirlpool-W10170080-Front Bearing

Front Bearing

PartSelect Number PS2338652

Used in Mixers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Touchpad does not respond.
  • Compare At

    $4.75
  • You Save

    $.79
  • Your Price

    $3.96
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Rear Bearing

Part Number 2341596

Used in Mixers.

$3.96
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 5 reviews What's this?
1-5 of 5
 

24 of 27 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDennis from Lake Mills WI

Mixer made very bad grinding noise, and would skip while making bread dough

1, REMOVED TRIM PIECE (1 SCREW)
2, REMOVED COVER (4 SCREWS)
3, REMOVED SPEED SWITCH ASSEMBLY (2
SCREWS)
4, REMOVED GEAR COVER (4 SCREWS)
5, REMOVED AND EXAMINED 2 WORM GEARS FOR WEAR. GEAR COVER WAS BADLY CRACKED, DON"T KNOW IF IT WAS CAUSED BY A PREVIOUS REPAIR OR BY HEAT, AS OLD COVER IS PLASTIC.
RECEIVED NEW PARTS AND INSTALLED THEM,
2 BEARINGS, 2 WORM GEARS, 1 NEW COVER OF DIECAST METAL AND A NEW GASKET.
ALL REPAIRS MADE WITH A #2 PHILLIPS SCREW DRIVER.
MY WIFE THEN MADE BREAD, AND IT PREFORMED FLAWLESSLY.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerStephen from Colorado Springs CO

Worm gear stripped.

Removed mixer motor housing by removing 5 obvious screws.
Removed plastic transmission cover by removing 4 obvious screws.
Down load parts exploded drawing from PartSelect.com
Found the worn part by the shiny teeth on the large gear.
Found the large worm gear on the drawing and ordered the gear, and associated bearings. Did not need the seal.
Removed worn part, assembled new gear and beargings in same manner as the worn part, and placed new part in mixer.
Replaced transmission cover gasket.
Repacked grease from transmission cover onto the new gear.
Replaced transmission cover (4 screws).
Replaced mixer motor housing (4 screws).
Replaced mixer trim band around the motor houseing joing. (1 screw).
Plugged it and and it works, good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerVincent J. from Hudson NY

Worn gears had to be replaced (second time)

the hardest part is removing the retaining ring (didn't buy pliers)after that it is very easy, remove ring, top gear, center pin, bottom gear,worm gear(was removed first)the grease is pretty nasty,clean off the old grease and put it all back the way it came apart,with new grease.And then PRAY !!!!!!! THANK YOU PARTS SELECT for your wonder smart staff.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerThomas from Upperco MD

Bevel gear, bearings and housing replacement

The parts I received from PartSelect were higher quality than the original parts. The bevel gear and housing were originally plastic. The new ones are solid metal. The machine sounds and runs better than it ever did. The drawings from the website made this really easy. This will be my first choise for parts from now on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGary from Hamburg MN

Gears and bearing failure

inspected and replaced worn components

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5