Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2332301
The terminals on the element are male quarter inch spade connectors. This part is found on the bottom of the oven.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
I opened the oven door, took two screws off and pulled the burnt one off and put the new one on. wow, it was so easy. My husband came home and said that he was going to install it. I told him that I had already install it. He could not believe it. I guess that women can be handymen too.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I took the racks out then took the two mounting screws out with a 1/4 in. nut driver.ThanksWM T BROWNE, JR
Most of the time I attributed to this repair was cleaning the stove in, around and in back of it after unplugging the stove. Next I used a nutdriver to remove the two retainer screws on the back of the oven. Then pulled the coil out with the wire connectors about 6 inches and pulled both of the connectors off old coil attached them to the new coil putting it back in place lining up the screw holes installed screws & tightened them up. I finished by touch up cleaning the coils of body oils due to touching the coils during install. Plugged it in, turned it on and viola! Thanks, sure beats the local appliance mechanic @ $45+/hr. Thanks again, I will look you up the next appliance that fails.
I unplugged the stove from the power plug in the wall. There are two screws at the back of the oven to hold the element in place. I removed the two screws. There are wire clamp inserts that attach to the element. Once the element was loose from the back wall of the oven, I gently pulled out the wire clamps. Removed the element. I laid the new element in the bottom of the oven and gently pushed the wire clamps into the new element. Re-attached the screws and put the power back into the wall and I was done. Easy, easy, easy. As for the drip pans, I pulled the element from the plug just under the stove top, cleaned the element and replaced the old drip pans with the new. Slid the element back into the plug and I was done.
I turned off the curcuit breaker, then removed the two screws holding the element in place and pulled it out to expose the connecting wires. The connectors resisted coming off at first but gentle pressure w/pliers did the trick. Then they slipped onto the new element easily, and I pushed the tips of the element back into the holes, replaced the two screws, and flipped the circuit breaker back on. Good to go in about 20 minutes!
I ordered the part and received it in two days. Using only a nut driver, (and after tuning off the electrical supply to the range), I removed the element, pulled off the attached terminal attachment, replaced the new element, connecting the new one to the wire terminals, replaced the nuts, turned on the power and was once again in business. Thank you. (P.S. I am a 70 year old grandmother)
First the power was turned off, then the oven door was removed. The two screws on the bake element were removed. Then the element was pulled out so that the wires were exposed, about 3 inched and disconnected. Put the new element in and placed the wires on the ends and pushed it back in place, put the 2 screws on, put the door back on. Turned the oven on and everything back to normal !!! Thanks part select for getting my part here so quick.
I turned off the circuit breaker. Unscrewed the two screws holding the bake element in place. Next, I pulled the element out and disconnected the wires. Reversed the process and I was done.I ordered the part from PartSelect.com and had it in my hands in less than 3 days--wow!!! Super fast shipping and the part worked perfectly. Thank you!
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire connectors from the lugs on the element. I then connected the new element in reverse order. Then I tested the new element by setting the controls to bake. That was the end of the repair rprocess.Thank you for your parts and delivery service.
When I removed the two screws, I discovered that one wire attached to the element was not attached. I had to open the back of the range (sheet metal screws) to find the wire, which was burnt and melted when I got to it. I had to run to hardware stroe to get a new connector, but once I had that the whole thing popped together quickly. I attached both wires to the element, screwed in the screws, and voila!
Removed the retaining screws in the clips attached to the element in the oven, and then remembered to OPEN the breaker before proceeding. Pulled out the bad element, removed the wires, and reversed the steps to install the new one.
First I turned off the electical supply to the oven.I unscrewed the nut bolts on both sides of the baking element and pulled the wires through. Disconnected the wires of old element, then connected the wires of the new element. Pushed wires back and connected the nut bolts to the back of the oven.The new element did not come with new screws so I used the old screws to connect the new element. The only problem is that after installing the new element my oven still does not work. It doesnt get any heat. Not sure what went wrong.
The heating element was defective. Unplugged the stove. Removed two screws from the bracket inside the oven that held in the element, pulled it forward, removed the two electrical spade connectors, and discarded the defective element. Removed the new element, put back on the two spade connectors, positioned the new element in place by pushing it back, screwed in bracket, replugged in stove, and tested.
Very simple. Unplugged the stove. Removed the back panel and connected the ends of the element to their electrical connectors.
First, I determined the problem by making sure that all other functions of the range were working... and they were. Then, I disconnected the power. After that, I pulled the range out from the cabinet space and proceeded to remove the back cover. Once the cover was off, I removed the two electric leads from the oven baking element and tested it for continuity. No continuity, so I ordered the new part. Once the part arrived (which was very quick) I reversed the procedure, and the bake cycle of the oven is functioning once again. Not a problem...
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.