Quick Question!

Have you ever purchased from PartSelect.com before?

2332301-1-S-Frigidaire-316075104-Bake Element - Push On Terminals - 240V
2332301-1-S-Frigidaire-316075104-Bake Element - Push On Terminals - 240V 2332301-3-S-Frigidaire-316075104-Bake Element - Push On Terminals - 240V http://www.partselect.com/Schematics/Frigidaire/L9ZDAD9Y.gif

Bake Element - Push On Terminals - 240V

PartSelect Number PS2332301

The terminals on the element are male quarter inch spade connectors. This part is found on the bottom of the oven.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.
  • Oven is too hot.
  • Little to no heat when broiling.
  • Touchpad does not respond.

Compare At

$20.58

You Save

$3.43

Your Price

$17.15
Order within the next 4 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 266 reviews What's this?
 

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Peggy from Owensville, MO

Oven lower element broke

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Earl from Elkin, NC

Bake element wouldn't heat.

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: JAVAD from KNOXVILLE, TN

Had no control on big burner

Replaced the switch very easily! Working great

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Edward from MILTON, PA

Oven did not heat

I watched your how to video and used my voltmeter to check my baking element. I found it defective and ordered your replacement. 5 or 6 days later it arrived in the mail. I installed it per the video and my wife baked a pizza to try it out. Perfect! Thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Susan from GERMANTOWN, NY

Bake element broken

Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Victor A from ATTICA, NY

Burnt bake element

open the door take out the racks.unscrew the holding screws for the element,pull it away from the back wall of the oven. take off the wires carefully and reverse the procedure

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Kristie from W VALLEY CITY, UT

One wire didn't come out

We took off the back to get the wires connected.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Nancy from Prosser, WA

Element burned out

unfastened clip at back of oven w/screwdriver. Pulled out the plug, unplugged the element. Plugged in new element, pushed back into place, refastened clip to hold it in place at back of oven.. Done

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Josh from SAINT PAUL, NE

Element burned out in the house we rent

Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Socket set
Customer: Scott from ALBANY, OR

Burned out bottom oven element

Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Very Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Daniel from CASTALIA, OH

Stove element stopped working

Unpluged Oven, Removed 2 screws, unpluged Element, Plugged in new element. Replaced 2 screws, plugged oven in. Done 15 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Horace from CRUMPLER, NC

Lower heat element burned out.

1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Mary from BAINBRIDGE, GA

Bottom heating element burned out.

Unscrewed 2 screws, pulled the wires out and unplugged the old element, plugged the new one in, screwed 2 screws back in, so easy anyone can do this, it's nice to have a second person holding a flashlight but couldn't be any easier.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Gerald from CANON CITY, CO

The lower heating element burnt through and front drawer glides broke.

Repair is simple and straight forward. Simply open oven door and remove oven racks. A philips #2 screwdriver is needed to remove 2 screws, 1 on each side at lower portion back of of oven..Slowly pull heating element out towards front of oven, wires will pull out with it. Simply wiggle and unplug spade connectors on each side, plug new ends of heating element into wires. Slide heating element back in re-attach removed screws not over tightening just till snug.

Front drawer glides: Remove oven drawer and this is a good time to give it a good solid cleaning. Clorox wipes and elbow grease. The handle can be removed to clean under neath as well just a few screws to remove with the same philips screw driver.

The front drawer glides do not mount on the drawer, they mount on each lower side of drawer opening above lower glides. There is a squared off small opening on each side for the glides to pop into with small square notches at the bottom of each hole.

Take the curved part of the glide and angle the insertion going into the hole turning down and pushing in, the glide will "Pop" or "Click" when seated.

That's it. Save time and money and fix it your self. You don't need to buy a new range when parts and do it your self are less than $30.00.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Carl from PORT ST LUCIE, FL

Bottom element had hot spots, very slow heating

Turn off the power to the range. Remove oven racks. Remove the two screws and slowly pull the element out being careful not to pull the wires off. Remove the two wires then attach them to the new element. Push the element back in place, put the screws back in, turn on the power and turn on oven to make sure the problem is fixed

Help other customers find the most helpful instructions.

Were these instructions helpful?