| |
2 of 3 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerPeggy from Owensville MO
Oven lower element broke
Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerLorene from Lewiston ID
It burned out
The new part was shipped and recieved very fast.
I removed the old one and installed the new one going by how I took the old one out. It was simple to do even for a 75 year old lady.. Thanks.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichael from Browns Mills NJ
Bake element broken
turn off power to oven at breaker box
remove screws holding bake element in
pulls wires off old element
put wires on new element
put the screws back in
turn the power back on
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerDon L from La Grande OR
Bake element began burning itself up.
Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!
The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.
Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.
The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Screw drivers
Customerraymond from irvine CA
Oven not heating up
ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsPliers, Socket set
Customerlynne from pelham NH
Bake element had stopped working
My husband had recently moved out of our house so I was very nervous about trying this repair myself but it was actually very easy!!I ordered the part on Monday, it arrived on Wednesday and Wednesday night I was baking dinner in the oven!!
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers
CustomerAngela from Ruidoso NM
While baking cookies I looked in the oven only to find the bake element was glowing white on the curve of the element, then a second spot started to burn. The element was fried.
The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMichael from Fort Worth TX
Replace the bake element
Had to remove the old element and had problems with the element shorted on the quick disconnect. After having my son unplug the appliance and cutting the quick connect off. My son then installed a new quick disconnect and the bake element.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerKeri from Raleigh NC
Oven element broke in three!
First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.
Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.
So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerKenneth from Wantage NJ
Bake element burned out
Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerDale from Athens TX
Didn't bake
Took it off, ordered a new part and put it back on.
Ordered on Monday and got the part on Tuesday.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerLaura from Hurricane UT
Heat element burned out.
The problem I ran into Was; Having the right socket size for doing the project. After taking care of that problem it was fairly easily to disconnect the element and reconnect the new one. It's pretty self explanitory.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerDonald from Canandaigua NY
Went go use oven and need heard a pop and dust smoke coming out vent , found lower element blew apart, since only store around was sears they didn't have part,so my son found your web site. So odered it came in 2 days, while going to order oven element we knew that one of the stove burner wasn't he
just unplug stove and unscrewed element out of back wall cleaned up mess and reinstalled. stove top you just pull out bake element and push back in
|
1 of 1 people found this instruction helpful
Parts Used
-
- Bake Element - Push On Terminals - 240V
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKaShira from Wilmington OH
Oven wouldn't heat
My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJim from Harrison MI
Lower baking element would not heat up.
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim
|