BBB A-Plus
2332301-1-M-Frigidaire-316075104-Bake-Element-Push-On-Terminals-240V.jpg
2332301-1-S-Frigidaire-316075104-Bake-Element-Push-On-Terminals-240V.jpg 2332301-3-S-Frigidaire-316075104-Bake-Element-Push-On-Terminals-240V.jpg

Bake Element - Push On Terminals - 240V

PartSelect Number PS2332301

This bake element is found on the bottom of the oven.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Little or no heat when baking
  • Cooktop element not heating
  • Oven not heating evenly
  • Will not start
  • Oven is too hot
  • Little or no heat when broiling
  • Touchpad does not respond
In Stock

  • Compare At

    $28.81

  • You Save

    $4.80

  • Your Price

    $24.01
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos

For installing this part.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 3 4 5 6 ... 16 NEXT > 46-60 of 234

 

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsWrench set

CustomerMitchell from Sebring FL

Banking element needed replacement

For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerLarry from Cowgill MO

Oven element burnt in several places

Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerRobynn from St. Louis Park MN

Bake element quit heating

Unplug the oven, open the door, take the screws out of the back wall that hold the small brackets which hold the element. Pull the element out of the wall, and pull a little of the wires with it to grasp easily. There are square nut screws, so you need the appropriate tool. Unplug the old element from the wires, and plug the new one in. Screw everything back together! This was a very easy fix!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerMarcus from Gastonia NC

Bake element burned into while baking

Take out 2 screws disconnect the wires one on each side removed element recoonnected the wires put the 2 screws back in . Also I did flip breaker off while working. When I turned the oven on I noticed it gets bright red almost instantly. I dont remember my old getting red at all. this tells me it probably needed changing a lot earlier. I ordered the part sunday nite it arrived wednesday at lunch.I will definetly use this co again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

Customerlori from Vermillion SD

My baking element went out in my over, it started on fire.

Very quick and easy fix. Used a nut driver to unscrew the bolts. Pulled it out and disconnected the two wires. I was very happy with the wonderful service we received from Partselect.com. I ordered the part Sunday evening and the part was here Tuesday by noon. I payed regular shipping charges. What a pleasant surprise!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerChris from Blacksburg VA

Oven would broil but wouldn't bake

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the new element, reassembled and SHAZAM. It worked. I am not good with electrical circuit testing etc. even though I know it must be easy so after reading many stories here, I decided to start by replacing just the element and see if I got lucky. I did. No need to call expensive repairman.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerMIRANDA from INDEPENDENCE KY

Element was sparking and coal hot red

UNPLUGGED OVEN, PULLED OUT OLD ELEMENT, REATTACHED NEW ONE, MAKING SURE TO BE CAREFUL WITH WIRES, AND PUT ON AS SECURE AS POSSIBLE, JUST LIKE IT WAS BEFORE...VERY EASY TO FIX

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPAUL from FRANKLIN NC

Baking element out

removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerSteve Gilliland from Delavan WI

Element cracked and sparked, no longer functioned

I UNPLUGGED the oven (very important), then I removed the two screws that hold the element in place, pulled the element out far enough to disconnect the two wires, plugged the wires on to the new element, pushed the new element back into place, and replaced and tightend the two screws. Finally, I plugged the oven back in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerScott from Pleasant Hill OH

Bake element went out

Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerCynthia from Roanoke VA

The bake element cracked in two

We called a local repair shop and they told us that it would take a month to get our part and it would cost over $50 for it. We went online and found PartSelect.com. The part was here in less than one week and it cost less than $40. My husband pulled the stove out from the wall took a screwdriver and unscrewed the screws, slipped in the new part and screwed the new screws in. It took him 15 minutes to fix it and now my stove works better than it has in many years!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerLuis from Corpus Christi TX

Burned out unit

Too dark to see, so left the power on so I cold use the oven light. Big mistake, shorted the fuse at the main box. No power in part of the house until finally figured out how to trip the fuse back on. Lesson learned. Never work on anything electrical without first turning off the power.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerJames from Bradenton FL

Baking element burned out

Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerIrving from Germantown MD

Oven element broke

It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Bake Element - Push On Terminals - 240V

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerMichael from Goddard KS

Oven wouldn't heat

using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 3 4 5 6 ... 16 NEXT > 46-60 of 234