Quick Question!

Have you ever purchased from PartSelect.com before?

2332301-1-S-Frigidaire-316075104-Bake Element - Push On Terminals - 240V
2332301-1-S-Frigidaire-316075104-Bake Element - Push On Terminals - 240V 2332301-3-S-Frigidaire-316075104-Bake Element - Push On Terminals - 240V http://www.partselect.com/Schematics/Frigidaire/L9ZDAD9Y.gif

Bake Element - Push On Terminals - 240V

PartSelect Number PS2332301

This bake element is used in electric ovens and ranges. It can be found in the bottom of the appliance. It supplies the heat required for the baking function. If your element is no longer glowing red, or your oven is not heating properly while the bake feature is being used, the element might be faulty. It features push on male terminals, which are 1/4-inch high temperature spade connectors. The bake element is approximately 19 1/4 inches wide, and it measures approximately 15 inches deep from the front of the element to the bracket. It extends 3 1/2 inches past the bracket to the terminals. Unplug your appliance before you begin any repair work.

This part works with the following brands: Frigidaire, Tappan, Kenmore, Crosley, Gibson, Westinghouse, Uni, Kelvinator.

This part works with the following products: Range, Microwave Oven Combo.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.
  • Oven is too hot.
  • Little to no heat when broiling.
  • Touchpad does not respond.

Compare At

$20.58

You Save

$3.43

Your Price

$17.15
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 279 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Bob from Casper, WY

Oven wouldn't heat

1. First unplug the range from the 220 outlet!!

2. Next I used a nut driver to remove the 2 screws that attach the bake element to the rear of the inside of the oven.

3. Pull the element toward the front of the range until you can unconnect the electrical wires by gently pulling on the connectors that attach the wires to the baking element.

4. Connect the new baking element to the electrical wires and re-attach to the rear of the oven with the two screws removed in step 2.

5. Plug the range back into the 220 outlet and test the oven......

It doesn't get any easier than that!! And to think that I was considering calling a repair man......

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Vicki from Tallahassee, FL

Baking element burned itself to utter destruction!

I removed the piece of old lower baking element by unscrewing the screws attached to the back firewall, removed the wires attached to the element, reversed the same proceedures and replaced the new baking element. Done! Baking as usual. Thank you for the timely response on sending the part. Ordered online, received the part the next day! I'm glad I found you and I look forward to using your services again whenever the need may arise.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Joseph from Alpharetta, GA

The bake element burned out

removed the screws that hold the bake element. Pull the wire away from the insulation. Hold the wire connector with pliers and pull the old element out. Squeeze the connector with pliers. Insert the new element connector to the wire and insert connection back into the original location.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: william from cleveland, TX

Element went bad

zip two screws out that held the element in place unplug the wire on each side and install the new unit and we are cooking again !

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Andjelko from North Port, FL

Bake element replacemetn

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Put the new elemetn back in place and that was it.

Really easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Wrench (Adjustable)
Customer: Nichelle from Washington, PA

The heating element in the stove broke

First of all this site has extremely fast shipping!! Ordered on a Sunday, had the part in hand the following Tuesday. I had read the other stories so I had a good idea of what to do so I unplugged my stove, I then loosened the two bolts holing the element in place, unhooked the wires to it, grabbed the new element, hooked the wires back up, screwed and tightened the bolts back up, plugged the stove back in and guess what...It Worked like a charm!! real quick and easy fix.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Sherri from Portland, IN

Non working bake element

Unplugged the oven, cleaned out the the sweeper front, back, inside oven, scrubbed and unscrewed the old and screwed in the new turned on and tada it was better than new:)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Thomas from Rome, GA

Heating element burned in half

Overall a very easy repair, but with one caveat to watch for. Used a nut driver to remove the two sheet metal screws on each side of the element and then slowly pulled the element out to detach the spade connector and wire from the back of the element.
Here is where to be cafeful: Take care to bring the end of the element wtih the wire attached through the hole without catching the connector. If the connector comes off behind the metal it could be a real bear to fish out. This didn't happen to me, but it could happen and turn a simple repair job into a headache.
Plugged the new element in and my oven works better than new. Great service from PartsSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: neal from sullivan, OH

Oven was not working

removed two screws with nutdriver ,pulled element out enough to expose wires, disconnected wires , removed element ,connected wires to new element, pushed element back into oven,replaced screws

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Judy from Littleton, CO

No heat in oven.

I removed the 2 racks in the oven, then the 2 screws, pulled out the old element, unplugged, discarded, set the new one in, plugged in, reaatced with thew 2 screws and reinstalled the 2 rack and was done. Works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Frank from Edgewater, FL

Burnt out lower element

remove two small screws in rear of oven. pull out element enough to expose wire connections and disconnect. remove old element and attach new one. just be sure power to stove has been turned off before begining repair. very easy..........

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Erin from Sewell, NJ

Bake element burned out

First, I shut off the electricity at the panel. Then I took out the 2 screws that hold the bake element at the back of the oven. Next, I separated the element from the wires and connected the new bake element and put the screws back in. Finally I turned the power back on to the oven and tested it. It worked perfectly! It all cost under $30 to do...it would have cost more than $100 to have a repair man come do it for me. The part came quickly and was packaged very carefully. Thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Nick from Bloomington, IN

Element had died and didn't work

Made sure the oven circuit breaker was off on the electrical panel in the garage then simply removed the two screws on the oven wall and pulled out the old element a couple inches. I then pulled off the connectors. Simply reinstalled the connectors on the new element, pushed it back in and replaced the two screws. After I turned the circuit breaker back on, I turned the oven to 300 to make sure it was working it's all good.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Bethuel from Arlington, TX

Lower element quit heating up

I have to give props to partselect.com!!!! I ordered the lower element on a Thursday and received it that very next Saturday!! I was surprised at the quck shipping. Anyway, it was just a matter of removing two screws and and then disconnecting the old element. I installed the new element and reinstalled the screws. Works like a champ. Thanks partselect.com!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Trina from Tacoma, WA

Bake element broke and wouldnt heat

first I unplugged the stove. then I pulled out the oven racks. I unscrewed the screws with a scocket. I pulled out the wires and disconnected. I then reversed the process to reconnect.

Help other customers find the most helpful instructions.

Were these instructions helpful?