| |
20 of 27 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerHigh Hope Employment Service from Milan MO
The handle to the door had been broken.
We had to remove the screws and take the door off the washing machine then the door glass ring. Replace and put it back on. It was really easy and save alot in repair bills.
|
7 of 8 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichael from Dexter MI
The plastic handle on the door of a front load washer cracked at the top.
I removed the two screws holding the old handle on and then then installed the new handle
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerFrancine from Wolcott VT
The door handle to the front load washer had broken off
Very easy. Remove 2 screws from the inside of the door. Take out the broken pieces and screw in the new one using the old screws.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customermandy from rock falls IL
Washer door handle broke
unscrewed the old handle, and screwed the new one on. It only took 2 minutes to fix. Very easy!!
|
3 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerBernard from Towson MD
Broken handle.
Removed screws and screwed in new handle.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMark from Gambier OH
Broken door handle
Very easy to fix. Diagram on web page was very helpful. Part was delivered over night. Great service.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMary from Oswego IL
Door handle broke off at the top
Like another commenter, my teenage daughter ripped the handle off at the top in a huff. My husband simply unscrewed the broken handle and replaced it with the new one. We now make sure to open the door from the middle of the handle, not the top.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMary from Lithia FL
Handle on the washer broke
One new door handle two screws and 5 minutes later it was like new again. Saved a bundle by doing the repair myself.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerMichael from cape may court house NJ
Door handle on outside cracked at the screws
removed the old handle held in by two screws lined up the new handle and reinstalled screws
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJames from Mt Holly NC
Door handle broken
Very simple fix - two screws out - replace handle and reinsert screws. The best part was how quickly I received the parts.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers
CustomerPaul from Fontana CO
No spin, broken handle, everything else worked
after clearing shelving. It took about 20 minutes to remove the dryer stacked on top, along with the gas line and the vent hose.....
Two screws and gently pry the back up with a screwdriver and the top pops off. open the door and remove the 2 screws while reaching down inside and the switch come right up with its 3 plug harness.
swap the old switch unit for the new one and slip it back down into place and reinstall the screws, and done in about 15 minutes.
my belt is in good shape so I will save the one I bought for later.
the handle is 2 screws and took less than 2 minutes.
It took about 20 minute to put the washer/dryer units back together and against the wall and running
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKenneth from Westminster MD
Handle was broken off
After locating the two screws on the inside of the door, I used a phillips screw driver, in a counter-clockwise motion, to take the screws out. I then removed the remaining pieces of the broken handle and then positioned the new handle in the holes seating it firmly in place. The handle had to be held into place while I negotiated the screws back into the holes turning the screws in a clockwise manner.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerJuan from Austin TX
The control console broke when we stacked some heavy item on the edge of this front load washer and the door handle broke from wear and tear.
First I removed the visible screws on the front of control panel. When I tried to remove it I realized it was also being held in place by the top coverof the washer. I next removed the screws holding the top cover in place and slid it back uncovering a few more screws holding the control console in place. The wiring pane was also held on the console with screws so i roved them and popped the old console out. After that I just replaced everything in reverse order and screwed the new console back in place. The door handle was alot more simpler. All I did there was open the door and remove the two visible screws on the inside of the door and the broken handle came off. I placed the new handle in place and screwed it on. These repairs were simple and once done I realized that it took no time at all.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customermelanie from lake worth FL
Washing maching door handle broke off. The replacement part cost 75% less than the manufactures part, and fits perfectly
arrived in 2 days. Using this company the replacement part cost me 75% less than the manufactures part, and it fits perfectly. It has a Slightly different color, but the price difference was huge. It was Very easy to install in only 2 minutes with a phillips screwdriver using the 2 screws provided. The manufaturer's part was $80 plus $11.00 shipping. This part cost me $25 with shipping. Amazing!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGeraldine from Lansing MI
Broken door handle
removed the two screws that were attached to the old door and put the new door on.
|