2329394-3-S-Whirlpool-W10169511-Ice Dispenser Motor Coupling
2329394-3-S-Whirlpool-W10169511-Ice Dispenser Motor Coupling 2329394-1-S-Whirlpool-W10169511-Ice Dispenser Motor Coupling 2329394-2-S-Whirlpool-W10169511-Ice Dispenser Motor Coupling

Ice Dispenser Motor Coupling

PartSelect Number PS2329394

This part attaches to the drive shaft of the ice dispenser motor.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Compare At

    $11.94
  • You Save

    $1.99
  • Your Price

    $9.95
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.6 / 5.0, 5 reviews What's this?
1-5 of 5
 

44 of 66 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerJack from College Station TX

Ice maker would not eject the ice either by cube or crushed

removed the Ice Tray, removed the cover that the motor is attached to, The biggest problem I had was getting the coupler off the drive shaft. It would not tightyen up and would not turn auger. I had to remove the unit and take a hack saw to cut the coupler off
The other problem I could not get the wireing harness unpluged from the refigrator, and had to remove each individual wire from its contact. I had to remove the whole motor unit inorder to get the old coupler off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 20 people found this instruction helpful

Parts Used

  • Ice Dispenser Motor Coupling

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerHAROLD from SPRING HOPE NC

Motor coupling weld broken

Removed four screws from ice maker motor/light support.Then unplugged electrical plug from side of freezer.Used two slip joint pliers to remove coupler from motor shaft. installed new coupler to shaft hand tight as will tighten as motor is run.Then reversed tear down order.
Ice dispenser works better than when we first got the refrigerator

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 30 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerRichard from Lynchburg VA

Ice dispenser won't eject ice cubes

I assumed the motor had burned out. I removed the 4 hex-head screws to remove the bracket holding the motor. I had to squeeze the electrical fitting to the motor located in the right rear of the compartment in order to electrically disconnect the motor, since the lower part of the fitting has a latch that prevents its easy removal. Then I could insert a vice grips on the shaft and on the coupling in order to (reverse) unscrew the coupling from the motor. I initially received the wrong replacement motor, but when the correct one arrived, it installed on the mounting bracket easily and I reinstalled the bracket with motor easily. It turns out a new motor did NOT fix the problem, so I'm not sure what to do now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 37 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

Customerjohn e from allentown PA

Motor was turning but no ice came out

took 4 screws out holding back cover of motor and un plug plug on right ps there is a tab to lift up before you pull plg use pliers to get off old coupling just keep unscrewing it till i catches good threads it will come off and put washers so you dont winde up back on to the striped part of the shaft. YOu rock price is good and the parts are right thanks john belzner

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 20 people found this instruction helpful

Parts Used

  • Ice Dispenser Motor Coupling

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Wrench(Adjustable)

CustomerLarry from Hague ND

Ice dispensor motor would run but would not dispense ice at the door!

To get the coupler off the motor shaft I took two adjustable wrenches and slit the old coupler where it was cracked.The threads on the motor shaft were stripped closest to the motor.I took two thin washers and put them on the motor shaft so the new coupler would not turn down to where the threads on the motor were sripped.Since the threads on the coupler are left hand they keep the coupler tight as the motor turns the dispenser auger to dispense the ice.I was a bit difficult to unplug the wiring harness but got it after we used a screwdriver to keep the tab bent down until the harness was unplugged.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5