2328901-1-S-Whirlpool-W10162384-Door Gasket
2328901-1-S-Whirlpool-W10162384-Door Gasket 2328901-2-S-Whirlpool-W10162384-Door Gasket http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/42457.gif

Door Gasket

PartSelect Number PS2328901

This oven door gasket comes with built in retaining clips.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Oven not heating evenly.
  • Little to no heat when baking.
  • Door won’t close.
  • Compare At

    $39.32
  • You Save

    $6.55
  • Your Price

    $32.77
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 13 reviews What's this?
1-5 of 13
 

37 of 46 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerLori from Scottsdale, AZ

Needed to replace oven door gasket.

First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerDavid from Bexley, OH

My wife destroyed the oven door seal with oven cleaner...

I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRandall from Katy, TX

Inner galls on door was craked

Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerDavid from Green Lane, PA

Oven would not come up to temp. That was set

Replacing the sensor kit and door gasket was no problem at all, however the baking element was A different story.
The problem was not the fault of the replacement part, but
the removal of the element to be replaced. The phillips head screws stripped out very easy and getting them out without damage to the interior finish of the oven was time consuming and challenging, but patients, and perservrance
win and so did I. Oven now works great

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Door Gasket

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers

CustomerJohn from Ashland, OR

Oven would stop heating after a few minutes of operation

Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 13