2326380-1-M-Whirlpool-UKF8001-Ice-and-Water-Filter.jpg
2326380-1-S-Whirlpool-UKF8001-Ice-and-Water-Filter.jpg 2326380-2-S-Whirlpool-UKF8001-Ice-and-Water-Filter.jpg

Ice and Water Filter

PartSelect Number PS2326380

This part has a high-quality carbon filter that reduces contaminants. Replace the filter annually or when the filter light is on. Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Water dispenser will not dispense water.
  • Ice maker will not make ice.
  • Leaking water.
  • Unusual Noise.
  • Fridge section too cold.
  • Ice maker dispenses too little ice.
  • Touchpad does not respond.
  • Compare At

    $59.38
  • You Save

    $9.90
  • Your Price

    $49.48
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 33 reviews What's this?
31-33 of 33
 

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customermichael from boca raton FL

Entire freezer compartment was cascaded in ice and icemaker had been noisy

Turn off power first or unplug. Get a light so you can see. Read these directions through one time to reduce the learning curve. Remove ice cube bin. 1/4" nut-driver will do most of the work. Remove flexible water fill tube from back of ice cube maker, move to the side, out of the way. Remove screw from "L" shaped bracket from the bottom of maker, close to the front. Two more 1/4" screws to go. There are (2) screws on the top left that hold the maker to wall. Loosen the front screw, but do not totally remove, unit will lift off of front screw. The back screw had to be completely removed because of a clip that holds the wiring on the back of the maker. The wiring is attached to the back wall in the form of what is called a Molex connector, a white plastic connector. This is probably the hardest part of the job, wiring access. The air deflector blocks any free access, so you have to just grab and depress the prongs to release the Molex from the wall. With wiring disconnected, remove entire assembly. Use a flat-tip screwdriver to pop the white cover off of the front of the maker to use on the new one. Same goes for the wire cube arm that sets out over the ice cube bin, taking the front out first (pulling straightout) then pivot arm 180 degrees and remove from back. Remove wiring harness from front of maker. Re-install on maker, it goes in one direction only, look at the configuration before you pull it out, and put in the same way. Make absolutely sure you re-install it so it clicks in all the way. If not, it won't work. I had to remove the ice maker again because I did not make this connection properly the first time. So I did the whole job twice. You have to put the job back in reverse of the way you took it out. The new one works great. I should have done this about a year ago. The old one had been making a noise and I ignored it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 62 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerEdmond K. from Las Vegas NV

Compressor locked up.

This is not a repair Job for just any body to do unless you have had some Refrigeration training and some experience !

I have been Certified and Licensed on refrigeration systems small, large and very large
for the past 36 years

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 38 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

Tools

CustomerHolly from Lowell IN

Handle on the french door (3rd door) freezer broke

I had to get on-line to find how to do it. It originally seemed easy enough, but it was not as easy as it looked. I sliced my finger trying to get the brackets into the butterfly clip, but after about 30 minutes of dogged-determination, I was successful...

The water filter replacement was easy, once I broke the tighter than all get out old filter.

Sure did save me a lot of money doing it myself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31-33 of 33