| |
5 of 8 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJOSEPH E from BRICK NJ
Microwave door handle broke
removed the 2 existing screws, aligned handle with holes, tightened screws.....done
|
3 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDonald from CHAPIN SC
Door handle broke off
I had to remove the two screws that were still in place from the broken door handle. Once they were removed I placed the new handle on the microwave and screwed the new handle in place. A total of less than 10 minutes!!!
|
4 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerLynne from Waxahachie TX
Handle on microwave fell off
There were globs of glue where handle was attached. Glue was brittle and chipped off rather easily. Ordered the new handle which arrived as the exact one needed and in 3 days with the lower cost shipping charge. The screws do not come with the handle but the old screws were still in the door and were removed easily with some needle nose pliers. Cleaned off appliance door and attached new handle in about 5 minutes or less. Used no new glue. A very easy repair.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJames from Smyrna TN
Old handle broke.
Removed the two screws holding the origional handle to the door. Attached new handle with same two screws. Job completed.
|
3 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKenneth from Las Vegas NV
The handle broke off are mirowave oven above are stove!
The repair was very simple. All we did was take two screws out and replace the handle and screw the new handle back on. That's it!!!
I thought the part was expensive but considering replacing the microwave it was well worth it!!
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerTom from Cupertino, CA CA
Handle broke
had to use pliers to grab a nub of the plastic screw female that had broken off. Other than that, went easy. This is a product defect and not only should the part be free, but there should be a free retrofit repair.
Your part was here quickly and perfect.
Great job, thank you.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerallan from Mayc Landing NJ
Broken handle
I went to use our microwave the Thursday before Christmas and the handle broke right off in my hand. I had to get to work and i did not tell my wife. By ten o'clock she called me and said the handle broke off when she used the microwave. I said I would try to find one and I did at PartSelect.The shipping I chose said 3 to 5 days.I placed the order about 2:30 that afternoon.The next day my wife called and said the handle had arrived and she put it on herself. Thanks for your prompt service, Allan Carignan
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerKelly from West Springfield MA
Handle broke off
Piece of handle was still wrapped around the screw..took a little while to get the old part off only took about 2 minutes to install the new part...it was a perfect match and fit perfectly.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerShelly from Pleasant Hill CA
Microwave door handle was broken
Removed a top and bottom screw. Pulled off the broken handle, put on the new handle, replace the 2 screws and about 60 seconds later, the repair was complete. Parts select seems to always have what parts I need and thats terrific.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerFRANKIE from NEW JOHNSONVILLE TN
Door handle broke
I first removed the broken door handle by removing two screws and replacing it with the new handle.The new handle was the exact size of the old handle,the holes lined-up perfect.I ordered the handle on thurs. and expected to get it the next week. I got the part Sat.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDavid from Catonsville MD
Door handle broke off
Removed remainder of door handle by unscrewing top and bottom. Screws were still intact and easy to remove. Replaced with new handle. Very simple. Ordering was easy and precise. Part received within 3 days. Schematic provided at website provided detailed information to ensure proper ordering.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLastenia from Bethesda MD
Door hadle broke
Unscrew old screws at the back of the microwave door and replace the old handle for the new one.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDavid C from Fort Wright KY
Handle broken at bottom screw connection
Opened microwave door,removed top and bottom screws (phillips), discarded old handle, put new handle in place, installed top and bottom screws in new handle, closed microwave door. Hard part was discarding the old handle because it required pulling out the trash can drawer(ha-ha).
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerSherry from Rutland VT
Door handle sheared off the microwave
The handle had been glued on previously, and broke off when I grabbed it. The glue had traveled into the holes where the plastic extends into the door for the screws to grab, so getting the screws and broken phalanges out was not easy. Using needle nosed pliers and an awl to scrape out the old glue worked, but it took some time.
Once I was able to get the screws loose and pop out the broken bits, the new part fit perfectly and is working like new.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCharles from Miramar Beach FL
Plastic door handle broke
Removed two screws and installed the new handle. The broken handle was no big deal.
|