This is a replacement haliant element for your cooktop or range. It is used with flat top ranges, and is found under the glass top of the range. This element is approximately 12 inches in diameter and is sold individually. The haliant surface element supplies the heat needed to the top of the cooktop. If your burner is not lighting up when it is turned on, you may have an issue with the haliant surface element. Be sure to disconnect power to the range before you begin this repair. To replace the element, remove the screws holding the cooktop in place, then remove it. Then, remove the screws holding the burner in place, disconnect the wires and replace the burner. Replace the cooktop and screw it back in to complete the repair.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Element will not heat
This part works with the following products:
Range, Cooktop.
This part works with the following products:
General Electric, Hotpoint.
Part# WB30T10130 replaces these:
AP4344395, 1474216
Customer Reviews
Average Rating:
★★★★★
★★★★★
15 Reviews
4.9
Filter By Rating:
5 Stars
14
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Rhonda K - January 19, 2024
Verified Purchase
Easy to install works great
Was easy to install and works great
★★★★★
★★★★★
Diane Z - January 7, 2024
Verified Purchase
Great service
Part arrived quick, exactly what I needed, fit perfect, my go to parts store.
★★★★★
★★★★★
Daniel K - July 23, 2023
Verified Purchase
Easy repair
Back up and running
★★★★★
★★★★★
John S - June 15, 2023
Verified Purchase
Worked well
All worked out well.
Ty
★★★★★
★★★★★
Derek S - March 7, 2022
Verified Purchase
Easy repair
Right part easy to install very happy will definitely use you again
★★★★★
★★★★★
Jessica R - April 18, 2021
Verified Purchase
Easy repair
??
★★★★★
★★★★★
Adriana R - April 18, 2021
Verified Purchase
Easy repair.
The part was in great condition. Arrive fast!
★★★★★
★★★★★
Edwin R - January 1, 2021
Verified Purchase
Good
Good
★★★★★
★★★★★
Jessie B - September 2, 2020
Verified Purchase
quick delivery, easy to install
it took me 15 minutes to install the burner,
★★★★★
★★★★★
David A - July 24, 2020
Verified Purchase
Part Works Great!
My Haliant Element that I ordered arrived quickly and securely packaged. After installation, the part worked good as new!
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 7 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
burner inside element not working
Being a front burner, I used a 24 in piece of wood to hold up range top. After removing to screws holding top. Made note of numbers on old burner and wire locations. Took off wires and three spring clips. Then replaced with new in numbered locations , wires next
Daniel from BURLINGTON, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large right burner would only light in the outside and would not stay on
Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was da
... Read moremaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.
Read less
JoAnne from LAMBERTVILLE, MI
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Wrench set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
12" Haliant Element would only work on the outer ring.
Watched repair videos on YouTube to prepare. The repair was very easy.
William from RICHMOND, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inside burner did not heat
Disconnect old burner and reconnect new one
Roberto L from LAUREL, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element went out in glass top stove.
Unscrewed the stove top and replaced the element.
Aleshia from O BRIEN, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
4 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Baking element and dual stovetop burner were fried
Baking element:First, turn off your breaker so you don't get injured. Using a small nut driver, remove the two screws that hold the element into the back of the oven. Once the screws are out, the element slides out, toward the oven opening. Be careful not to pull too hard, or the wires could disconnect from the back and be difficult to re
... Read moretrieve. Once the wires are exposed, disconnect them from the terminals. Attach them back to the new element, and put it back in. EASY For the stovetop, this is a glass top, so the burners are underneath. There are two small screws on the underside of the stove top, where the oven door closes. Remove those screws and then lift the front of the entire stove top. It will hinge at the back. There are two screws and little metal brackets that hold the burner in place. Remove those screws and brackets, disconnect the wires, and be sure to remember which wire goes where. Reattach the wires and screw the brackets back into the burner. Refasten the stovetop and you are good to go.
easily lifted the top of the stove after removing two small screws in front of the stove.removed screws holding burner in place , disconnected some wires and replaced burner. be sure to turn off the power before beginning this project
matthew from waterford, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
19 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
16 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Huarong Li
November 11, 2017
Two large burners (#57, 58) got out order. When turned on but the internal small burn at the center does not heat up. Very likely, the wire is broken. Can i just order the burners? What is the price for each? Thanks, huarong li
For model number JP80DM2BB
Hi Huarong,
Thank you for your inquiry. If the center burner is not heating up, you will need to check the switch that turns it on or the element, the wiring between the switch element and element itself with a multimeter. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Ulises
January 29, 2018
On my stove part 57 and 58 burners when turned on only outer circle heats up not the center if part is bought and replaced will it work again?
For model number JB850SF4SS
Hi Ulises, Thank you for the question. The issue would be with the Element or the switch that controls the element. I suggest testing both parts with a Multi Meter to determine the defective part. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
December 18, 2019
A follow up to my last question: How do you test the heating element to determine if it has failed? The element is an expensinve part and want to be sure i need to replace it.
For model number GE JB655SKSS
Hello Michael and thanks for writing.
Take the elements out of the stove, it's time to check them. Set your multimeter to resistance times one and touch the probes to the wire terminals. This should give you an even reading. Now place one probe on the wire terminal and the other on the element. The needle should not move. If there is no continuity or if the needle moves with these tests, you will need to replace your heating element as this means there is a malfunction. We hope this helps. Please contact us anytime.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Joan
December 7, 2022
I am not sure of the size it is the big burner that went out on my stove. I’m not sure of the size if you could help me with it I appreciate it. Thank you.
For model number PB970BOM2BB
Hello Joan, thank you for reaching out. We have researched your model and found that this element, part number PS2321564, is approximately 12 inches in diameter. Please contact customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
January 18, 2023
The twelve inch dual heating elemnet only the outside ( or hi) is working. Should I replace both the switch and the element? And what part numbers do I need? Thank you!
For model number Jb655sk2ss
Hello Robert, thank you for reaching out. The issue seems to be with the Surface Element and you may need to replace it, the part number is PS2321564. If that does not help, we would recommend replacing the Element Control Switch, part number PS11729102. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
The element heat indicator light is always on for the large 12" element. It heats up for a minute then shuts off. It can't sustain heat when trying to place a pot on it.
For model number CBC980STSS
Hi Bryan, thank you for reaching out. Based on our research, you may need to replace the element, part number PS2321564, to fix the issue. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tom
October 29, 2019
Dual ring surface elements can not reduce heat on either ring with control knob
For model number JB655DK3WW
Hello Tom, Thank you for the question, In most cases this means the switch that controls the element will need to be replaced. PartSelect Number PS11729102. Hope this helps!
Do the range top heating elements have a thermostat control. It seems one of ours may be overheating. Can this crack the glass top?
For model number GE JB655SKSS
Hello Michael and thanks for writing.
No, there is not a thermostat there. It certainly sounds more like a faulty element check for signs of damage and replace it if needed. Yes, it could damage the glass top. We hope this helps. Please contact us anytime.
We do carry related parts for units just like yours. For example, part number PS8754842 Good luck with your repair.
My burner is stuck on the "high" setting and won't lower no matter the knob position. Is this a burner problem or something with the wiring, or something else?
For model number JB860DJ1WW
Hello Crystal, Thank you for the question. This is an indication the Switch that controls the Element is defective and will need to be replaced. We hope this helps!
