| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDerek from Pittsford NY
Plastic door handle cracked and broke off door
removed the interior door seal with thin scraper. Then removed screws. Replaced "new handle" and reverse process. Process is easy but the handle part is ridiculously expensive for what it is!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJohn from Yorktown Heights NY
Cheap plastic handle on microwave broke again
Open the microwave door. Remove the exposed screw in the top left hand corner. Using a knife, pop off the plastic moulding that surrounds the glass out to expose the screw in the bottom left hand corner of the door. Remove that screw. (note they are two different types and lengths). Attache the handle and screw in the top screw, then the bottom screw. Re-attache the moulding around the glass. Close the door and reopen with new handle.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGary from Mountain View CA
Microwave door handle was broken.
Used thin spatula to remove plastic frame around inside of door to expose bottom screw. Removed top and bottom screw and pulled off broken handle. After cleaning up the outside of the door, installed new handle and tightened screws. Popped plastic frame back into place: done!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerD Katherine from Pittsfield MA
The handle broke off.
ordered the handle it was so easy to installed with help fron do it yourselfers.thanks
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerSusan from Granbury TX
Old handle broke off of the microwave
We planned on buying a new microwave but thought well, we would see if there was a part available for a 13 year old microwave. Lo and Behold! Partselect.com had one! It was shipped and we got it in a couple of days. By reading what others (professional installers) said about putting the new handle on, I was confident to let my husband tackle this on his own! We saved a service call and now it works like new!! Thanks
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMike from Arcata CA
Broken bottom of door handle
unsrew top handle screw on inside of door, removed handle, slid handle plate out slid new one in (probably would not have had to replace this part but the part makes the job look better) removed snap in trim finish around window inside door, fished out old screw and broken plastic from handle, srewed new handle on, snapped trim back on and job was complete.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerdaniel from Champaign IL
Broken handle
Repair was two screws 2 times lefty loosy - 2 times righty tighty - two minutes tops.
I was more impressed by how fast Partselect got the part to me less than 23 hours from online order to sitting on my stoop. Great job !
|
0 of 9 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers
CustomercHERYL from NASHVILLE TN
Melted stirrer cover, broken door handle
poped stirred cover off and replaced, easily.
where door handle had broken off I needed pliers to hold the plastic part of the door handle in order to unscrew the top of the handle from the door. I was unable to figure out how to get to the other screw and a friend completed the job for me. Wallah, new handle, looks like new, works perfectly. 1/3 the cost of replacement. Probably could have done without ordering one of the parts but it wasn't that much.
|