Quick Question!

Have you ever purchased from PartSelect.com before?

232100-1-S-GE-WB15X10020        -Door Handle
232100-1-S-GE-WB15X10020        -Door Handle 232100-2-S-GE-WB15X10020        -Door Handle 232100-3-S-GE-WB15X10020        -Door Handle http://www.partselect.com/Schematics/GE/00010523i01.gif

Door Handle

PartSelect Number PS232100

Screws are NOT included.

This part works with the following brands: GE, Hotpoint & Kenmore.

Compare At

$83.58

You Save

$13.93

Your Price

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Handle

Part Number 232260

This white handle does NOT come with the screws.

$84.22
No Longer Available

Tapping Screw

Part Number 234666

$2.35
No Longer Available

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 38 reviews What's this?
 

2 of 2 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: barbara from san diego, CA

Broken door handle

Did as describe by others who had replaced the handle.
Remove the inside trim (carefully) to get access to screws that we holding the remaining handle pieces.
Attach the handle with the exist screws, replace the trim. Done in about 5 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Mike from Arcata, CA

Broken bottom of door handle

unsrew top handle screw on inside of door, removed handle, slid handle plate out slid new one in (probably would not have had to replace this part but the part makes the job look better) removed snap in trim finish around window inside door, fished out old screw and broken plastic from handle, srewed new handle on, snapped trim back on and job was complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Derek from Pittsford, NY

Plastic door handle cracked and broke off door

removed the interior door seal with thin scraper. Then removed screws. Replaced "new handle" and reverse process. Process is easy but the handle part is ridiculously expensive for what it is!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Michael from Woodbridge, VA

Handle on the microwave broke

The Parts select diagram and order ing process made it very easy to complete my repair job. After receiving my parts, I unscrewed the screws with a phillips driver. Then I popped out the handle. There is one tricky part - the screw is a bit too small for the existing whole and so I added a washer to fix this problem. I then slide in the new handle. Very easy!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Eduardo from San Antonio, TX

Door handle broke

unscrewed the old handle and screwed the new one on really quick.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Cheryl from Fairview Heights, IL

Our handle broke off completely

The handle worked great, the only thing was that it didn't come with the screw for the handle and I thought it would. The part description was very vague. So we have the bottom part of the handle super-glued and found a scrap screw that we could use for the top. At least it was better than no handle.

Thanks much,
Cheri Morena

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: John from Yorktown Heights, NY

Cheap plastic handle on microwave broke again

Open the microwave door. Remove the exposed screw in the top left hand corner. Using a knife, pop off the plastic moulding that surrounds the glass out to expose the screw in the bottom left hand corner of the door. Remove that screw. (note they are two different types and lengths). Attache the handle and screw in the top screw, then the bottom screw. Re-attache the moulding around the glass. Close the door and reopen with new handle.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Cristy from Waynesburg, PA

The handle snapped on the door.

2 screws off and 2 to put it back on. Not hard at all. Quick and easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Douglas from Angola, IN

Door handle broke off

I first pulled the bottom left and left side inner 3/8th inch rounded liner out. Use a thin flat head screw driver to gently pry the inner trim piece out of place. This exposed the bottom screw. I pulled out the old 1/2 inch silver coarse thread screw. The top screw is obvious. Removed that. I had to replace the face plate which slid off. Replaced the new face plate then put in the new handle top male end then the bottom male end in the holes. I screwed in the top 1.5 inch browm fine thread screw. Don't over tighten, just go until snug. If you over tighten you may crack the plastic walls of the screw hole built into the handle. I then put the small screw in and tightened it. Then snap the trim piece back in place. Viola.......You are done

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Douglas from Angola, IN

Handle broke off, bulb burned out the broke trying to get it out.

Once on your web site it gave me a skematic of my microwave which showed me how the parts connected. I saw how easy it was and I saw what type of bulb it was I ordered the parts and it took less than 15 minutes to repair. Thank you so much for your site, It is now on my favorites list. Doug

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Gerald from Lindstrom, MN

Broken door handle

I looked at what others ahd said about the repair and just followed their instructions. Just took off the top screw of the handle, used a butter knife to pry off the plastic cover around the inside door and took off the bottom screw of the handle. Put the new handle on and put the screws back and pushed the door frame back in. Very easy to do and took very little time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Richard from Weston, FL

Handle broke at attachment point

the top screw is plainly visible, the bottom screw is not and may give pause. If you remove the plastic ring, on the interior face of the door, it will give access to the bottom screw for the handle. While you have the handle off, remove the backing plate for the handle, on the front of the door by pulling outward, gently until it pops off. Then you can slide the front glass panel out and clean it. {CAUTION: do not spray any cleaner on the exposed glass with the mesh on it, it will be impossible to remove any liquid and will cause fogging when you replace the outer glass panel}. Replace clean glass panel, and handle backing plate, make sure it snaps in fully so the screw holes line up properly. Screw on new handle, replace plastic ring and you are back in business.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: William from Bristol, WI

Handle broken at bottem

Believe it or not, all the advice given by others was right on the mark. Unscrewed the top piece, worked the seal off, which was easier then I worried it would be, removed the screw from the broken piece and reversed the process. Even my wife was surprised I was able to complete the repair with no problems. THANK YOU for the help. Bill

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Door Handle
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jan from Sparks, NV

Microwave door handle broke at bottom

Followed the instructions from the do-it-yourselfers on your web site which were all excellent and a wonderful asset to your site. It took us much longer than 5 minutes (about 20 min.) because we couldn't get the bottom screw out and then had one heck of a time screwing it into the new handle. Don't know if the srew was too long, too big or what, but we feel confident that it won't fall out!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: KELLY from ARLINGTON, VA

Broken microwave handle

Unscew top screw, remove seal from inside door, remove bottom handle screw, replace w/ new handle, replace seal.

Help other customers find the most helpful instructions.

Were these instructions helpful?