| |
1 of 2 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerGary from St. Augustine FL
The oven door would not open all the way
After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerDave from Glenview IL
Broken door hinge
The part arrived on timed and fit perfect. The repaired took 1/2 hour and everything works perfect. My wife thinks I am the best
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerYvette from Galt CA
Oven door hinge roller was broken
It was extremely simple! I removed the oven door and the storage drawer, unhooked the spring, and unscrewed the hinges. Removed the broken hinges and screwed in the new hinges, hooked the springs back on, slid the oven door back on and replaced the storage drawer! Presto! The repair is complete
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerArthur from Northridge CA
Plastic roller on right hinge was broken
Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRoderick from Pleasanton CA
Plastic roller on hinge had broken causing door not to open easily
Slid door off hinges. Removed 3 screws which hold hinge in place. Removed drawer to access spring for hinge. Gasped at all the crumbs and crap which had collected underneath the drawer. Cleaned up crumbs+crap from floor. Disconnected spring from hinge and removed old hinge completely. Installed new hinge with 3 screws. Attached spring to hinge - center hole fitting. Slid drawer back in place. Angled hinges outward in order to re-install door. Slid door back onto hinges. Door now operates nice and smoothly. Job well done.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerArthur from Silver Spring MD
Replace oven door right hinge
I really can't add much more to the very good instructions already posted. You will need a flashlight to see the spring -- when connected it stands vertical with one end connected to the hinge. There are 3 holes you can connect to -- I used the middle one, #2. The other end of the spring is anchored to a hole/slot in the stove frame. It is very easy to position this spring. Be careful though, there's a lot of sharp sheet metal in there. You will need a phillips head screwdriver to remove/install 3 sheet metal screws that fasten the hinge to the stove.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerAngelina from San Diego CA
Broken roller on hinge
Removed the oven door. Released spring on hinge. Removed 3 screws. Removed broken hinge and replaced new hinge reversing these steps.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCharles from Bourbonnais IL
The plastic guides on the hinges were broken.
I removed the door by pulling it up (according to the instructions). Than took a philips screwdriver and
removed the three screws in each hinge, unhooked the springs
and slid the old hinges out of the slots.
The new hinges slid into the slots perfectly so the screws
were installed, the springs rehooked and the door installed.
Real simple.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerMatthew from Gardnerville NV
Broken plastic wheel on the hinge assembly
Pulled the three screws off unhooked the spring then removed the hinge. attached the the new hinge to the spring put the screws back in slid door back on took less than 15 minutes.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerandrew from hudson WI
Door was hard to open
After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJoe from Matthews NC
Hinge on oven door neede to be replaced
First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerTami from Mount Vernon WA
Oven door was not opening all the way
The plastic wheel glide that the hinge runs back and forth on was worn off on one side so it was grinding and binding.
Remove storage drawer from under oven. Open the door to the special catch position and carefully lift door off the hinges - (not by the handle, hold onto both sides).
Take out three screws w/ a hex head nut driver, slip the hinge down into the hole, look under drawer area w/ flashlight and carefully unhook spring, while holding onto spring- pull old hinge out, see which hole has wear (that's the one you want to use of the three), insert new hinge all the way in and hook up spring. Pull hinge out and line up front plate w/ holes, insert 3 screws snugly. Done, awesome probably saved a 200.00 visit from the appliance guy. My husband thinks I'm amazing!
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerRussell from Brea CA
The oven door would not open or close all the way. The plastic hinge roller guides broke on both sides.
Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )
|
0 of 2 people found this instruction helpful
Parts Used
-
- Hinge with Roller - Right Side
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichelle from Saint Petersburg FL
The right hinge was broken and the door would not close properly.
I removed the door by pulling up and away from the hinges. I then removed the drawer. I unhooked the tension spring by hand and noted the opening. I then removed the three screws on the hinge assembly, removed the ole part, and replaced it with the new one. I replaced the tension spring and slid the door back on to the hinges. I did it all in less than 10 minutes.
|