231612-1-S-GE-WB14X104          -Hinge with Roller - Right Side
231612-1-S-GE-WB14X104          -Hinge with Roller - Right Side 231612-2-S-GE-WB14X104          -Hinge with Roller - Right Side http://www.partselect.com/Schematics/GE/GE_Thumb/00010092i04.gif

Hinge with Roller - Right Side

PartSelect Number PS231612

This hinge is located on each side of the oven door.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Door won’t close.
  • Compare At

    $36.54
  • You Save

    $6.09
  • Your Price

    $30.45
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Hinge with Roller - Left Side

Part Number 231611

This hinge is located on each side of the oven door

Order within the next 6 hrs and your part ships today!
$36.09
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 29 reviews What's this?
1-5 of 29
 

37 of 38 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerFrank from Pebble Beach, CA

The right side hinge assembly broke. Replaced both sides

First I removed the door by lifting it off the hinge assemblies.

Then I removed the drawer to access the spring.

Removed the spring, noting which attachment hole was used.

Removed the hinge assembly with a Phillips screwdriver.

Replacef the unit.

Repeated for the other hinge assembly.

Note: it took longer to find the correct parts in the parts diagrams than it did to replace them.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 16 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPeter from Framingham, MA

Oven door hinge rollers broke, hard to open door

Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so long as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerRichard from Winchester, MA

Oven door jammed,could not open it

Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Hinge with Roller - Right Side

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCraig from Kernersville, NC

Oven door hinge roller deteriorated, oven door hard to open.

Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Slid door back down onto hinges. Done in four minutes flat!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJames from Westfield, NJ

Both hinges broke.

Real simple. Disengaged springs at the inside bottom, replaced hinges and reengaged springs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 29