Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS231280
The flat style gas oven igniter included in this kit has a body length of 3-3/4". This kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to range wiring using porcelain wire nuts. This part is used to heat your oven.
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
First, I removed the two screws that held the heat shield in place. Second, I removed the one screw that held a small wire covering. That covering kept the wires inside the back wall of the range. Third, I removed the two screws that held the Igniter Kit, and unplugged it from the back of the range. I then carefully put the new igniter in, and reassembled everything in reverse order. It only took about 30 minutes to do the repair, and 30 minutes of cleaning and wiping of the broiler area. (It is amazing what you see when you take things apart). I should have been wiping things up over the past few months. Overall, a very easy repair. I ordered the part at 12:30 in the afternoon, and FedEx delivered it the next morning at 11:30, all for the regular shipping price of $6.95. VERY HAPPY.....
Help other customers find the most helpful instructions.
Were these instructions helpful?
first I thought it was a faulty gas valve, so I pulled it out, started researching for a replacement part, found your site and started research. I discovered thhat the igniter was the culprit, that info. saved me about a week of time and a 100 bucks, so I installed the gas safety valve back in the oven, patience is the word for the day, you cross thread this and you are done! any way ordered ignighter and it shipped to my house in about 4 days, New York to Calif. had it installed in about 15 minutes fired off the oven and ...IT worked hurray...10-9-2010,
1. Pulled the 110V power plug. It was not necessary to turn off the gas; just be careful not to stretch or pinch the flexhose behind the stove.2. Removed the oven door by opening a couple of inches then lifting upward.3. Removed the warming drawer by pulling out to the stop, then pushing the small levers on the side of the track to release.4. Removed two flathead screws at the back of the oven to free up the oven bottom panel.5. Removed the bottom panel by lifting up the pack until the front edge clears the overhang.6. Removed the two screws on the side that hold the igniter to the burner tube. Be sure not to let the screws drop into the gaps in the oven floor. Note the position of the bent tab with the holes to ease aligning the new part.7. Reached through the warming drawer to release the plug by squeezing the tabs on the end.8. Pulled the plug up through the gap in the oven floor (where the wires went through) and connected it to the other connector.9. Ran the new wire down through the oven floor.10. Aligned the new igniter and tightened them. Had trouble getting the screws started so I used a toothpick to align one hole while starting the other screw.11. Replaced the oven bottom panel. It needed a little jockeying to get the screws and holes aligned.12. Replaced the door.13. Replaced the oven drawer.This turned out to be a good time to clean all those dusty places that don't get cleaned that often.
Step 1. Pull oven out disconnect power,turn off gas & remove gas line from stove.Step 2. Remove broiler drawer,locate igniter & safety valve.Step 3. Disconnect 2pin molex connector for igniter and faston connectors fromvalve.Step 4. Use nut driver remove fasteners that hold igniter and valve remove gas line and feedfrom valve.Step 5. Replace valve and igniter.Repeat steps 4-1 and start baking.Note: You may only need a igniter and not a valve,both were bad on my unit.Most often it's just the igniter that goes out.
After removing the bake tube and ignitor assembly the following day for a close inspection which involved removal of the bottom pan, racks etc. and disconnecting the ignitor / tube assembly by unscrewing the sheet-metal screws holding them in place, I discovered that the ignitor had burned a hole in the bake tube which could not be seen without unscrewing the ignitor from the tube first. This caused the air / propane ratio to dramaticly change causing the oven to have a strong odor, start to carbon up the bake tube and effect the temperatures and cook time and the possibility of monoxide fumes effecting the chef. The parts that partselect.com supplied, which were in stock ,worked perfectly and saved my Christmas goose. Happy Holidays!
Once I figured out how to get the top off it was not too bad. all of the screws and igniters for the burners had to be removed. The actual install of the thermostat was simple after that. The igniter was also an easy install. Overall, it takes more time to disassemble the stove to get to the problem than to install the part.
1. removed old oven glow igniter using nut driver socket--it wasn't that tight so I didn't have to use the actual driver. The igniter was now loose hanging from its 2 wires.2. on the web I read that the new part would have to be spliced to the old, however I was able to push the old igniter through a hole in the oven wall and then pull it out of an adjoining hole on the right hand side. With some effort I detached the old igniter from a plug receptacle that leads back up to the main wiring junction of the oven.3. I then plugged the new igniter into the receptacle, pushed it back into one hole, then fished it out of the other hole. I could then reattach the new igniter onto the gas delivery tube. Turned the oven on and it worked.
First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the wires.I had tried to get a replacement element from Sears but their new element did not have the proper connecter and was missing the flange on the side that the screws went. I am very pleased that I was able to get the exact replacemen part.
1. Pull the oven out to access the connector in the back of the oven near the bottom center to disconnect the connector to the ignitor. Then push the connector and wire through the hole in the back of the oven.2. Removed the broiler drawer to access the ignitor.3. Removed the two screws holding ignitor to the burner bar, then pull wire the remaining way through the rear hole.4. Installed the new part with the two screws to the burner bar.5. Insert the wires with connector througth the hole in the rear of the oven to reconnect to the plug at the back outside of the oven Reconnect the connector at the back of the oven.6. Push the oven back in place and it is ready to use.
This repair was fairly simple, just took the door off, then the 2 screws in the back, lift the bottom out. then remove shield to valve unplug the old igniter. then put it all back in reverse order. it worked great.
Take out inside of oven.Igniter is held on with 2screws and electrical clip.take off old one and put on new one.
I removed the whole burner (3 screws) and the igniter (2 screws). IGNITER comes from Mfg. boxed with wrong plug on igniter - however they supply two porclean nuts so that the wires can be cut and joined. I recommend that you use the plug off the old igniter and splice it to the new part, so that it will plug into the stove's existing plug
1. Moved oven from the wall.2. Unplugged the stove from the electrical outlet.3. Removed over racks and bottom panel.4. Located wires leading from the igniter in the back of the stove. 5. Disconnected the wires from the ignitor.6. Used socket set to remove screws from ignitor. 7. Cut connector plug from new ignitor. 8. Stripped about a half inch of insulation from wires of new ignitor to be able to connect it to stove. 9. Carefully handled new ignitor and screwed it into place. 10. Attached wires of new ignitor using new caps. 11. Put bottom panel and racks into place. 12. Plugged oven into electrical outlet - Oven ignited and made a good dinner.
It all began one find night baking and suddenly the oven would not light up. And so for the next few years all I ever used the stove for was for stove top cooking, See Im a single guy so its not in my nature to get to fancy when it comes to cooking home meals,but after a while the mood changes and you finally get up the motivation to fix whats wrong. The change over went easy,easier than I expected.And the part worked just fine. As far as ease of the order and receipt,couldnt have been better,I got the part within 48hrs and that is fast! Thanks to all.T.Melillo
first i removed the screws that held the element and put the other one on. still would not heat . so i took the back of stove ,sides of stove loose to trace wires and under the top of stove i found a wire that comes from oven switch had been bitten into by a mouse wire nutted and electrical taped the wire back togeather and it workes fine . keep in mind there are 3 thinge that could be wrong. it goes from the switch, to the gas valve in broialer to the igniter switch,gas,fire .
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.