229118-1-S-GE-WB07T10230        -Door Vent Trim
229118-1-S-GE-WB07T10230        -Door Vent Trim 229118-2-S-GE-WB07T10230        -Door Vent Trim

Door Vent Trim

PartSelect Number PS229118

This part works with the following brands: GE, Hotpoint & Kenmore.

  • Compare At

    $108.92
  • You Save

    $18.15
  • Your Price

    $90.77
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 3 reviews What's this?
1-3 of 3
 

9 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerStephen L from Fairland OK

Staining/ burnt paint on door trim and drawer front

Simply pull out the drawer, four screws hold the front panel on, remove and replace the front panel. For the door trims, with the drawer removed, take out three screw on the bottom of the door, tilt door outward, take out two screws at the top inside of the door. This separates the outer shell from the door. Retaining screws are now exposed for the trims. Simply remove and replace the trims one at a time being careful the proerly align the glass front panel.Replace the front shell back on the door assembly. It is helpful to have an extra set of hands to hold it in place while reassembling.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used

  • Door Vent Trim

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsSocket set, Wrench set

CustomerJennifer from Spanish Fork UT

The trim vent piece on the door of my oven was damaged when I used the "self clean" on it. A towel hanging on the handle started smoldering and stuck to it leaving a bad burn mark.

I first used an Allen wrench to unscrew the two screws that held the back of the oven door to the front. Then when I got that apart it revealed about 12 other screws that held the handle and trim vent piece on together. I unscrewed each of those with the socket set (it took me a while to find the exact size I needed). I took off the handle and trim piece and slid the new piece onto the slots, put the handle back on and then worked in reverse order to screw all the screws back into their places. The only problem was that I didn't realize some of the screws were a bit longer than others and by the time I took them all off and went to screw them back in, I realized that I hadn't noticed which places needed the longer ones and which had the shorter ones. So if you are doing this repair note that not all the screws are the same and you will want to remember which ones go where before putting them in a big pile like I did. After all the screws where in place I pushed the back of the oven door together with the front and used the Allen wrench again to screw them tightly together. Pretty easy overall- at least for a housewife!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerAndrew from Boynton Beach FL

Over door trim burnt / discolored

I had an estimate from GE to repair my oven door that burnt and discolored after 8 years of service, the estimate was $386.00 to repair the gasket and install new door trim.

I found the repair parts on this website and was very surprised the parts only cost $120.00. Even better, the items were shipped same day and received the very next day...Excellent! The repair was so easy and took less than 30 minutes. PartSelect is the best!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3